Introduction

Thank you for choosing the active DisplayPort 2.0 fiber optic AOC cable. With this cable, you can transmit DisplayPort signals up to 100m without external power supply. The cable is a hybrid cable containing both optical fibers and copper wires.
Our DisplayPort Active Hybrid Cable is the most competitive DisplayPort connection solution on the market. It supports a maximum data rate of 10 Gbit/s per channel, is lightweight, flexible, and has a very small bending radius of only 48 mm.
With the embedded advanced optical engine, the DisplayPort Hybrid Cable provides full signal integrity.

Intended Use

Use is only permitted indoors, i.e., not outdoors. Contact with moisture, e.g., in bathrooms or similar, must be strictly avoided.
For safety and approval reasons (CE), do not modify and/or alter the product. Using the product for purposes other than those described above may damage the product. Furthermore, improper use can cause hazards such as short circuit, fire, electric shock, etc.
Please read the user manual carefully and keep it for future reference. Only pass the product on to third parties together with the user manual.

Safety Instructions

Please read the user manual carefully and pay particular attention to the safety instructions. If you do not follow the safety instructions and information on proper handling in this user manual, we accept no liability for resulting personal or material damage. Furthermore, in such cases the warranty/guarantee will become void.

This product is not a toy. Keep it away from children and pets. Do not leave the packaging material lying around carelessly. It could become a dangerous toy for children. Risk of suffocation!

The maximum tensile load of the cable is 300N (30kg). Never pull the cable with a higher load. The minimum bending radius of the hybrid cable is approx. 48 mm. Bending the cable below this radius will irreversibly damage it.

Beware of trip hazards; ensure the cable is installed securely.

Protect the product from extreme temperatures, direct sunlight, strong shocks, high humidity, moisture, flammable gases, vapors, and solvents.

Do not subject the product to mechanical stress. If safe operation is no longer possible, take the product out of service and protect it from unintended use.
Safe operation is no longer guaranteed if the product:

• shows visible damage
• no longer functions properly
• has been stored for an extended period under unfavorable environmental conditions, or
• has been subjected to significant transport stresses.

Handle the product carefully. The product may be damaged by impacts, shocks, or even falls from a low height.

Also observe the safety instructions and operating manuals of the other devices to which the product is connected.

Consult a specialist if you have any doubts regarding the operation, safety, or connection of the product.

Scope of Delivery

• 1x DisplayPort 2.0 AOC cable
• 1x User manual DE/EN
• 1x Safety warning

Features

• Support of DisplayPort 2.0 specification with data rates up to 40 Gbps
• Support of HDCP1.4 and HDCP2.2
• Support of HBR3
• Low RFI / EMI profile for sensitive applications
• Support of resolutions up to Ultra HD 8K (7680x4320) 85Hz, 4:4:4
• Lossless support of DisplayPort audio formats
• Supports EDID including self-recognition function
• Long-term bending radius (48 mm)
• Plug & Play connector
• Low power consumption: < 0.5 W per connector (power required)

Application

• Digital Signage
• LED Signboards
• Home Cinema
• Blu-ray, 3D video, projectors, set-top boxes, DVR, game consoles and computers
• TV broadcasters
• Conference rooms
• Video devices
• Security systems
• ... and more

Specifications

Mechanical Properties & Environmental Compatibility

*D = the diameter of the cable body, in this case 4.8mm

Specifications

Environmental conditions

Construction

Cable construction

Cross-Section

Structure

Hybrid cable, optical fiber (High Speed data), copper (Low Speed signals)

Cable construction

• 4 fiber cores and 8 copper conductors
• Cable sheath: PVC
• Diameter: 4.8 mm
• Plug dimensions: 46.9 x 20 x 12.3 mm
• Connection material: zinc alloy

Operation and Connection Diagram

Note: The FX-I260 series is designed to be used with a +5V passive Power Delivery provided over the DisplayPort connection by the source device. This +5V connection, as well as the power supply for the integrated optical fiber module, is transmitted over a pure standard copper connection to the Receiver. Please ensure that the source device can supply more than 500 mA.

Caution: This cable can only be used in one direction. The connectors are labeled “SOURCE” and “DISPLAY”. Each plug must be inserted into the correct device to avoid signal loss.

Note: Before using this cable, make sure that all devices connected to the AOC DisplayPort cable are switched off and not powered.

Connect the “SOURCE” side of the DisplayPort plug to the Transmitter and the “DISPLAY” side of the other DisplayPort plug to the Receiver/display. This works without additional power supply.

Note: We advise against using additional cables or adapters between the connectors, as this may weaken the signal transmission performance.

1. Switch on the DisplayPort source device and the display.
2. If the system does not function properly, please read the chapter FAQ – Troubleshooting in the next section.

FAQ - Troubleshooting

The display shows:
• A black screen
• A distorted image
• Interference noises

1. Check that the connectors are in the correct sockets of the source and Receiver devices; check the markings on the plugs.
2. Ensure that the DisplayPort plugs are firmly inserted into the DisplayPort source and the DisplayPort display.
3. Verify that the DisplayPort source and the DisplayPort display are switched on and properly started.
4. Reset the system by unplugging and reinserting the “Source” and “Display” connectors.
5. Restart the system with the connected DisplayPort cable.

Maintenance

There are no parts inside the product that require maintenance by you; therefore, never open/disassemble it.
Have maintenance, adjustment, and repair work carried out exclusively by a professional or specialist workshop.
If you have questions not answered in this user manual, please contact our technical customer service or an expert.

Cleaning

Before cleaning, disconnect the product from connected devices.

Note: Do not use abrasives, solvents, aggressive cleaning agents, rubbing alcohol, or other chemical solutions, as this may damage the casing or impair functionality.

For cleaning, a dry, soft, and clean cloth is sufficient. Do not press too hard on the housing, as this will cause scratch marks. Dust can be easily removed with a long-haired, soft, and clean brush.

Warranty and Liability

The manufacturer grants the statutory warranty of 2 years on a new product.

Note: Since the manufacturer has no influence on the installation of the product, the warranty and guarantee cover only the product itself.

If a fault or defect is detected in your product, please contact your specialist dealer and, if applicable, present your receipt or invoice as proof of purchase. Your dealer will either repair the fault on site or forward the product to the manufacturer. You greatly assist our technicians if you describe any faults in detail – only then can you ensure that even rare faults will definitely be detected and eliminated!

Note: The manufacturer is not liable for personal injury or property damage resulting from improper installation, operation, or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than that described in this operating manual is prohibited and leads to loss of warranty, guarantee, and liability.

CE Compliance

Hereby PureLink GmbH declares that FX-I260 complies with Directive 2014/30/EU.
The full text of the EU declaration of conformity is available at the following internet address:
www.purelink.de

Disposal of Devices

WEEE Reg. No.: DE 93847290

Electrical and electronic equipment must not be disposed of with household waste according to the European WEEE Directive. As a consumer, you are required under the ElektroG to return electrical and electronic devices free of charge at designated public collection points or to the point of sale at the end of their life cycle. Details are regulated by the respective national law. The symbol on the product, the user manual, or the packaging indicates these regulations. By disposing of old devices in this manner, you make an important contribution to protecting our environment.

Disclaimer

The product complies with statutory national and European requirements. All company names and product designations contained herein are trademarks of their respective owners.
All rights reserved.
We reserve the right to make printing errors and changes to the device, packaging, or manual.

Legal & Compliance

Product identification

Model: FX-I260-015 – manual version 1.0

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.