页 1
TV Floor Cart and Accessories
INSTALLATION MANUAL
Caution: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
PDS-0011C 100" MAX
200x200, 300x300, 400x200, 400x400, 600x400, 800x400, 800x600, 1000x600
80kg (176lbs) RATED
| Component | Max Weight |
|---|---|
| TV | 80kg (176lbs) |
| DVD | 5kg (11lbs) |
| CAMERA | 5kg (11lbs) |
Maintenance
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
- Please contact your distributor if you have any questions.
9. Adjustment
- 1200mm, 1250mm, 1300mm, 1350mm, 1400mm, 1450mm, 1500mm, 1550mm, 1600mm, 1650mm TV panel center height measured from floor.
- Loosen the screws on both support blocks to adjust the DVD shelf to the desired height then tighten all screws to secure.
+5° -10°
B1 support block
页 2
Caution: Read the entire instruction manual before you start installation and assembly.
- Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
- This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
- Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
- Tighten screws firmly, but do not overtighten. Overtightening can cause damage to the items and greatly reduces their holding power.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
Note: Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
| Component | Qty/Remark |
|---|---|
| PDS-0011C | |
| left leg | B (x1) |
| right leg | C (x1) |
| left cover | D (x1) |
| right cover | E (x1) |
| middle base | A (x1) |
| Package M | |
| washer | M-F (x4) |
| M8x20 | M-C (x4) |
| M5x14 | M-A (x4) |
| M6x14 | M-B (x4) |
| big spacer | M-H (x4) |
| M6x30 | M-D (x4) |
| M8x30 | M-E (x4) |
| small spacer | M-G (x8) |
| plastic handle | G (x2) |
| universal plate | F (x1) |
| right adapter bracket | K (x1) |
| left adapter bracket | J (x1) |
| top cover | L (x2) |
| connecting plate | N (x1) |
| camera shelf | O (x1) |
| DVD shelf | M (x1) |
| fastener | P (x2) |
| cross bar | Q (x1) |
| support bar | R (x1) |
| knob | S (x2) |
| M6x16 | T (x4) |
| M4x6 | U (x3) |
| M4x6 | V (x2) |
| M5x6 | W (x2) |
| M6x25 | X (x2) |
| left column | H (x1) |
| right column | I (x1) |
| M6x14 | Y (x6) |
| M8x25 | Z (x8) |
| allen key | B1 (x1) |
| M6x25 | A1 (x2) |
| wrench | C1 (x1) |
页 3
C1Wrench (part identifier)
2. Attaching the Column to the Base
T B1 B1Screw types/parts identifiers
1. Assembling the Base
Caution: Please hold the inner column when loosening the screws to adjust height. Adjust to the desired height, then tighten all screws. Repeat this step for the left column.
Note: Make sure both columns are at the same height using the height indicator as guide.
B1 G H I PPart identifiers
Insert the fasteners into the column rails.
Note: Make sure both fasteners are at the same height, then tighten screws on the fasteners to secure.
Note: Now the columns are attached to the base without the use of any screws. Be careful not to knock the columns over.
I B A CPart identifiers
- Insert the right leg into the base. Align the holes in the right leg to the holes in the base. Secure with the screws. Repeat this step for the left leg.
- Each castor can be adjusted independently for fine tuning. Slightly turn the nut to lower or raise the base.
X XScrews/Parts identifiers
页 4
W Y L QScrew types/Part identifiers
- Attach the cross bar to the fasteners using appropriate screws and then tighten all screws using a suitable screwdriver.
- Attach the universal plate to the columns using appropriate screws.
- Tighten all screws using a suitable screwdriver.
F D E B1 S A1 Y Z RPart identifiers
- Use appropriate screws to secure the columns to the base.
- Tighten all screws using an allen key.
- Attach the DVD shelf to the support bar using the appropriate screws and the knobs.
3. Assembling the DVD Shelf
页 5
4-1 For Flat Back Screens
M-A/M-B/M-C M-FChoose according to screen type
4. Installing the Adapter Brackets
Attach the support bar (attached to the DVD shelf) to the supporting blocks using appropriate screws. Tighten all screws using an allen key. [supporting block]
Note: Please adjust the columns assembly to the desired height before installing the display.
4-2 For Recessed Back Screens or to Access A/V Inputs
- Tighten all screws but do not over tighten.
- Position the adapter brackets as close as possible to the center of the display.
- Screw the adapter brackets onto the display.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
or or or
M-C M-F M-G
M-C M-D/M-E/ M-F M-G
M-D/M-E M-F M-H
M-D/M-E M-F M-H M-GBracket mounting combinations
5. Hanging the Display onto the Universal Plate
- Hook the adapter brackets (display attached) onto the universal plate.
- Rotate the bottom screws counterclockwise to lock.
- Rotate the bottom screws clockwise to unlock.
- Use the padlock to prevent display from being stolen (Padlock is not included).
IMPORTANT: Make sure the display is mounted correctly before releasing it.
B1 B1 X B1Screw/Part identifiers
页 6
Remove the screws.
8. Installing the Connecting Plate
- Attach the connecting plate to the universal plate with the removed screws.
- Tighten all screws using a suitable screwdriver.
7. Installing the Camera Shelf
U VScrew types
6. Cable Management
- Attach the camera shelf to the connecting plate using appropriate screws.
- Tighten all screws using a suitable screwdriver.
O CPart identifiers
Legal & Compliance
Product identification
Model: PDS-0011C – manual version 1.0
Warranty and liability
The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.
The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.
Trademarks and disclaimer
Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.
Packaging
Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.