页 1

Flat Panel Mobile Cart and Accessories

INSTALLATION MANUAL

Caution: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

200x200/300x300
400x200/400x400

600x400

PDS-1001C 70"
MAX 80kg (176lbs) RATED
80kg (176lbs) RATED

Optional Accessories

Note: The accessories are not standard. The accessories will be selected according to user requirement.

• 10kg (22lbs) RATED
• 10kg (22lbs) RATED
• All accessories

页 2

WARNING

Note: Read the entire instruction manual before you start installation and assembly.

• Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

• column (x1) B
• cable clip (x6) E
• wheel caster (x2) D
• wheel caster/brake (x2) C
• fixing piece (x1) F
• top cover (x1) G
• universal plate (x1) H
• adapter bracket (x2) I
• base (x1) A
• wrench (x1) J

• washer M-F (x4)
• M8x20 M-C (x4)
• M5x14 M-A (x4)
• M6x14 M-B (x4)
• big spacer (x4) M-H
• M6x30 M-D (x4)
• M8x30 M-E (x4)
• small spacer (x8)
• M8x15 (x6) M-G
• M8x40 (x3) P-A
• 6mm Allen key (x1) P-B
• D8 washer (x6) P-D
• P-E
• M8x15 (x3) P-C

页 3

2.Attaching the Column to the Base

1. Assembling the Base

• Insert the casters into the holes of legs and hand thread to secure.
• Attach the casters with brake to the long legs.
• Attach the casters without brake to the short legs.
• NOTE : Lock the brakes on the casters to avoid sudden movements during installation.

Attach the column to the base using three screws and tighten all screws to secure them.

PDS-1504

PDS-1502

PDS-1503

PDS-1501

• host machine rack (x1)
• J 5mm Allen key (x1)
• P-F Package P
• 5mm Allen key (x1) P-H
• iron shelf (x1) K
• shelf support (x1) L
• M5x10 P-G (x3) Package P
• laptop box (x1) M
• 5mm Allen key (x1) P-J
• key (x1) P-I
• Package P support rod (x2) N
• camera shelf (x1) O
• M5x12 P-K (x4)
• 2mm Allen key (x1) P-L
• Package P J

页 4

3. For the model PDS-1504 installation

Installing the Host Machine Rack

• Loosen the both washers leaving 4mm space from the iron plate.
• Put the host machine in the rack and push gently one side of the rack to keep it close to the host machine then tighten the knobs to secure. For security, please buckle up the belt.
• Loosen the knobs to pull one side of the rack to make it keep the maximum space.
• Insert the host machine rack to the desired position along the column slots. Tighten all screws with an Allen key to secure.

4. For the model PDS-1502 installation

Installing the Iron Shelf

• Insert the shelf support to the desired position along the front slots of the column. Tighten the two screws to secure it.
• Attach the iron shelf to the shelf support using three screws, tighten them with a proper screwdriver.

页 5

Use the key to open the laptop box.

6. Installing the Universal Plate

5. For the model PDS-1503 installation

Installing the Laptop Box.

• Insert the laptop box to the desired position along the column slots. Then tigten all screws to secure.
• Put the laptop into the box gently then close the box and lock it.

Loosen the two knobs on the fixing piece to make it easy to insert the column.
Insert the fixing piece to the desired position along the back slots of the column. Level the fixing piece and tighten both knobs.

+3° -3°

X X√

Attach the universal plate to the fixing piece using screws and washers provided. Level the universal plate then tighten all screws with an Allen key.

页 6

Insert the top cover into the both support rods.
Remove the two caps from the camera shelf, Attach the shelf to the support rods using four screws and tighten all screws to secure it and then reattach the caps to the camera shelf.

7. For the model PDS-1501 installation

Installing the Camera Shelf.

camera
Loosen the screws(but don't remove) on the bottom of support rods.

Use three screws to fasten the top cover.
display size .）along the column slots and tighten both screws to secure the support mount.
Use three screws to fasten the top cover.
Insert the support rods to the desired position (Determine the position for support mount keeping in mind display size.) along the column slots and tighten both screws to secure the support mount.

8. Installing the Top Cover

9. Installing the Adapter Brackets

Top of the display

页 7

9-1 For Flat Back Screens

• Position the adapter brackets as close as possible to the center of the display.
• Screw the adapter brackets onto the display.

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

• M-A
• M-B
• M-C
• M-F

9-2 For Recessed Back Screens or to Access A/V Inputs

• Tighten all screws but do not over tighten.

• M-C
• M-D
• M-E
• M-F
• M-G
• M-H

10. Hanging the Display onto the Universal Plate

Tighten the bottom bolts to secure the brackets to the universal plate.

11. Cable Management

1211

页 8

Maintenance

• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.

Use the cable clips for routing cables.

1413

Legal & Compliance

Product identification

Model: PDS-1001C – manual version 1.0

Warranty and liability

The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.

The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.