← Products
PureMounts® Touch Screen TV Stand - Single Display up to 70"
Discontinued

PDS-1101S

PureMounts® Touch Screen TV Stand - Single Display up to 70"

PureMounts® Touch screen TV Stand - Single Display up to 70".

ManualFAQ
PDF / print
Chapter 1 of 5

页 1

Flat Panel Display Floor Stand INSTALLATION MANUAL

Caution: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

200x200/300x300
400x200/400x400

600x400

PDS-1201S 70"
MAX
70kg (154lbs) RATED
70kg (154lbs) RATED
200x200/300x300
400x200/400x400

600x400

PDS-1101S 70"
MAX

Maintenance

  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).
  • Please contact your distributor if you have any questions.

7. Adjustment

45°
90°
Loosen the tilt handle to adjust the display to obtain the desired angle then tighten it.

Note: Tilt handle can be pulled out due to a limit amount of space.

+3° -3°

Chapter 2 of 5

页 2

NOTE: Read the entire instruction manual before you start installation and assembly.

Package P
Package M

  • Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
  • This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
  • Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
  • Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

Component Checklist

  • washer M-F (x4)
  • M8x20 M-C (x4)
  • M5x14 M-A (x4)
  • M6x14 M-B (x4)
  • big spacer (x4) M-H
  • M6x30 M-D (x4)
  • M8x30 M-E (x4)
  • small spacer (x8) M-G
  • cable clip (x5)
  • base (x1) A
  • column (x1) B
  • tilt plate C (x1)
  • universal plate (x1) E
  • adapter bracket (x2) F
  • 5mm Allen key (x1) P-C
  • M8x15 (x7) P-A
  • M8x40 (x3) P-B
  • 6mm Allen key (x1) P-D
  • rubber pad (x4) (Peel off the backing paper from the rubber pad and stick the rubber pad on to the supporting foot.)
  • D8 metal washer (x3) P-E
  • D8 plastic washer (x4) P-F
  • D8 metal washer (x4) P-G

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

Chapter 3 of 5

页 3

2.Attaching the Column to the Base

1. Attaching the Tilt Plate to the Column

  • Attach the column to the base using the appropriate screws and washers, Then tighten all screws to secure them. (B, A)
  • Attach the tilt plate to the column using the appropriate screws and washers. Then tighten all screws with an Allen key to secure it. (B)
  • Attach the universal plate to the tilt plate using the appropriate screws and washers. Then tighten all screws with an Allen key to secure it. (E)

3.Attaching the Universal Plate to the Tilt Plate

4. Installing the Adapter Brackets

Top of the display F

Chapter 4 of 5

页 4

4-1 For Flat Back Screens

TV
TVTV
M-A
M-B
M-C
M-F

4-2 For Recessed Back Screens or to Access A/V Inputs

TV
TVTV
Tighten all screws but do not over tighten.

  • Position the adapter brackets as close as possible to the center of the display.
  • Screw the adapter brackets onto the display.

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

or or or
M-C M-C
M-D
M-E
M-F
M-G
M-F
M-G
M-D
M-E
M-F
M-H
M-D
M-E
M-F
M-H
M-GM-G

5. Hanging the Display onto the Universal Plate

Tighten the bottom bolts to secure the brackets to the universal plate.

6. Cable Management

Use the cable clips for routing the cables.

Was this helpful?
← PreviousNext chapter →
Staff sign-in