页 1

Flat Panel Mobile Cart/Floor Stand and Accessories

INSTALLATION MANUAL

Caution: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

PDS-2501 PDS-2502
200x200/300x300 400x200/400x400

600x400

PDS-2032S 70"
MAX
60kgx2 (132lbsx2) RATED

60kgx2 (132lbsx2) RATED

PDS-2505

PDS-2032C 70"

MAX 200x200/300x300 400x200/400x400 600x400

10kg (22lbs) RATED

10kg (22lbs) RATED

All accessories

14. Adjustment Maintenance

• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please contact your distributor if you have any questions.

+3° -3°

+5°

-10°

Optional Accessories

Note: The accessories are not standard. The accessories will be selected according to user requirement.

PDS-2503 PDS-9501

页 2

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

PDS-2032C/PDS-2032S WARNING

Note: Read the entire instruction manual before you start installation and assembly.

• Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

connecting piece (x1) K
top cover (x1) N
left (x2) I
adapter bracket

3mm Allen key (x1) S
M8x40(X4) R
right (x2) J
adapter bracket
column (x1) M
5mm Allen key (x1) T
6mm Allen key (x1) U
M8x16 (X4) Q
M8x65 (x8) P
cable clamp (x8) O
D8 steel washer G (x8)
D8 plastic washer H (x8)
M8 L (x4)
left cover C (x1)
right cover D (x1)
base B (x2)
middle base (x1) A

Component (PDS-2032C only)

supporting foot (x4)
Y caster wheel/brake V (x2)
caster wheel W (x2)
wrench (x1) X

Component (only PDS-2032S )

rubber pad (x4) Z
(Peel off the backing paper from the rubber pad and stick the rubber pad on to the supporting foot.)
universal plate 2 (x1) F
universal plate 1 (x1) E

页 3

1. Assembling the Base

Attach the left and right base to the middle base using the appropriate screws. Tighten all screws with an Allen key.

2. For the model PDS-9501 installation

Note: Assembly based on the accessories selected by user.

3. Attaching the Column to the Base

Attach the power socket to the back of column using the appropriate screws. Tighten all screws with a phillips screwdriver. Attach the column to the assembled base using the connecting piece, secure them with the appropriate screws.

Note: Lock the brakes on the casters to avoid any sudden movements during installation.

P U T-H R U G

PDS-2505

PDS-2502

PDS-2503/PDS-2504

PDS-2501

Package P
key (x1) P-F
M6x8 (x4) P-D

PDS-9501

power socket (x1) T-H
M6x8 (x4) P-A
4mm Allen key (x1) P-B

PDS-2503 only

D6 washer (x4) P-E
connecting piece (x1) T-E
ST4.8x9.5 (x4) P-G

Note: The following accessories are optional.

P-G

Note: With the brake wheels facing forward.

A B B

页 4

4. Installing the Covers

5. For the model PDS-2505 installation

Note: Assembly based on the accessories selected by user.

5-1: Installing the host machine rack on the back of the column

Insert the host machine rack to the desired position along the column rails. Tighten all screws to secure it with an Allen key.

Peel off the backing paper from the silicone pads and stick the silicone pads onto the host machine rack.

Attach the connecting piece to the host machine rack using the appropriate screws. Tighten all screws with an Allen key.

Note: With the arrow pointing upward.

T P-B P-C T-B T-A T

5-2: Installing the host machine rack on the side of the column

Note: If the power socket is installed on the back of the column

• Loosen the screws in order to separate the metal plate from the connecting piece.
• Attach the previously removed plates to the host machine rack using the previously removed screws.
• Tighten all screws with an Allen key.
• Insert the host machine rack to the desired position along the column rails. Tighten all screws to secure it with an Allen key.

T T

metal plate
metal plate

页 5

Insert the laptop box to the desired position along the column rails, Tighten all screws to secure it with an Allen key.

P-F T

• Use the key to open the laptop box.
• Put the DVD into the box gently , then close the box and lock it.

DVD

6. For the model PDS-2502 installation

Note: Assembly based on the accessories selected by user.

Insert the iron shelf to the desired position along the column rails. Secure it by tightening screws with an Allen key.

• Put the host machine in the rack and push gently on one side of the rack to keep it close to the host machine, then tighten the knobs to secure.
• Use the adjustable buckles to hold the machine firmly in place.
• Loosen the knobs to pull one side of the rack to make it keep the maximum space.

knob
buckle

7. For the model PDS-2503 installation

Note: Assembly based on the accessories selected by user.

Note: With the arrow pointing upward.

P-D P-E

Attach the connecting piece to the laptop box using the appropriate screws and washers. Tighten all screws to secure it with a proper phillips screwdriver.

T-E T-D T-C T

页 6

10. Installing the Universal Plate

Insert the universal plate to the desired position along the column rails. Tighten all screws to secure it with an Allen key.

Note: With the arrow pointing upward.

11. Installing the Top Cover

Attach the top cover to the column using the appropriate screws. Tighten all screws with an Allen key.

T

8. Assembling the Universal Plates

O U Q N

12. For the model PDS-2501 installation

Note: Assembly based on the accessories selected by user.

• Remove two plastic caps for the camera shelf installation.
• Tighten the support rods to the camera shelf.

T-G T-F

Attach the universal plate 1 to the universal plate 2 using the appropriate screws, washers and nuts.

9. Installing the Cable Clamps

HG L H

页 7

13. Installing the Adapter Brackets

For Flat Back Screens

Insert the support rods to the desired position (Determine the position for support mount keeping in mind display size.) along the column slots and tighten both screws to secure the support mount.

For Recessed Back Screens or to Access A/V Inputs

Tighten all screws but do not over tighten.

• Position the adapter brackets as close as possible to the center of the displays.
• Screw the adapter brackets onto the displays.

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screens.

页 8

14. Hanging the Displays onto the Universal Plates

• Lift the display carefully and pull downward two straps at the same time, then hook the adapter brackets to the universal plate. Fasten the adapter brackets to the universal plate by releasing the straps.
• The other display is hung onto the universal plate in the same way.
• Use the padlocks to prevent the displays from being stolen (The padlocks are not included).

13. Cable Management

Run the cables through the cable clamps and the rubber strip.

Legal & Compliance

Product identification

Model: PDS-2032C – manual version 1.0

Warranty and liability

The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.

The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.