Tilt Wall Mount
PM-BT200
Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.
Caution: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
Note: Do not attempt to install this product if you do not understand the instructions or have any doubts about the safety of the installation.
Note: This mounting bracket was designed to be installed and inspected by qualified personnel only.
Note: The wall or mounting surface must be capable of supporting the combined weight of the equipment and all attached hardware and components.
Note: Do not use this product for any purpose not explicitly specified by manufacturer.
Caution: Improper installation may cause property damage or personal injury. The manufacturer will not be held liable for any damage or injury due to incorrect mounting, incorrect assembly or incorrect usage.
Note: DO NOT install this product near a heat source.
IMPORTANT: Ensure that you have received all parts according to the component checklist (inside this manual). If any parts are missing or faulty, telephone your local distributor for a replacement.
Note: MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least once every three months).
Tilt Wall Mount illustration
75x75100x100200x100200x200
VESA pattern symbols
23-42''/ 58-107cm
35kg (77 lbs) RATED
PureLink GmbH
Von-Leibniz-Str. 1 48432 Rheine | Germany
Phone: +49 (0) 5971 800 299 0
Note: PureLink GmbH hereby declares that this product complies with Directive 1907/2006/EU and 2011/65/EU.
Parts List
- A (x1)
- B (x2)
- C (x1)
- M6x30 (x4) M-A
- M8x30 (x4) M-B
- D8 (x4) M-C
- (x4) M-D
- W-A (x4)
- W-B (x4)
- W-C (x4)
Step 1
- Check compatibility with the wall type before installation.
- Use the correct drilling and mounting methods for your wall type.
- Do not use a hammer drill on a drywall.
Step 2
- Use screwdriver to attach the mounting brackets (B) to your TV using screws (M-A/M-B), washers (M-C), and spacers (M-D) if necessary.
Step 3
- Hang the TV with brackets onto the wall plate.
- Secure the TV by tightening the locking screws.
- Two people recommended for this step.
Step 4
- Adjust the vertical angle of the TV between 0° and -14°.
Legal & Compliance
Product identification
Model: PM-BT200 – manual version 1.0
Warranty and liability
The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.
The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.
Trademarks and disclaimer
Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.
EU conformity
PureLink GmbH hereby declares that this product complies with Directive 1907/2006/EU and 2011/65/EU.
| Directive / Regulation |
|---|
| 1907/2006/EU |
| 2011/65/EU |
The full text of the EU Declaration of Conformity is available at: www.purelink.de
Packaging
Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.