Installation Manual

TV Wall Mount

PM-EASYFLEX-52 / PM-EASYFLEX-65

• 55" max: 30kg (66lbs) rated. Do not exceed rated listed weight. Serious injury or property damage may occur!
• 70" max: 30kg (66lbs) rated.

Safety Precautions

Tip: Read the entire instruction manual before you start installation and assembly.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

• Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
• This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

Component Checklist

• Package M: articulated arm assembly (x1)
• A: bottom horizontal bar (x1)
• C: top horizontal bar (x1)
• B: adapter bracket (x2)
• D: bumper pad (x4)
• G: thumbscrew (x1)
• H: plastic stopper 1 (x2)
• E: plastic stopper 2 (x2)
• F: plastic cover 1 (x2)
• I:
• Package W: ST6.3x55 (x3)
• W-A: concrete anchor (x3)
• W-B: D6 washer (x3)
• W-C: M5x14 (x4)
• M-A: M6x14 (x4)
• M-B: washer (x4)
• M-F:
• M8x20 (x4)
• M-C: big spacer (x4)
• M-H: M6x30 (x4)
• M-D: M8x30 (x4)
• M-E: small spacer (x8)
• M-G:

Installation

Caution: Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended. Installers are responsible to provide hardware for other types of mounting situations. Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

1a. For Wood Stud Wall Mounting

Note: Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

1b. For Solid Brick and Concrete Mounting

1. Find and mark the exact location of mounting holes.
2. Drill pilot holes ø 4.5mm (ø 3/16"), depth 55mm (2.2").
3. Screw the wall mount onto the wall.

1. Mark the exact location of mounting holes.
2. Drill pilot holes ø 10mm (ø 3/8"), depth 60mm (2.4").
3. Screw the wall mount onto the wall.

Mounting the Brackets and Bars

2. Mounting the Plastic Covers

Note: Pull the articulated arm and make it vertical to the wall, insert both top and bottom plastic covers.

3. Assembling the Adapter Brackets and Horizontal Bars

Adjust the brackets to fit mounting holes on the back side of the TV. Then tighten screws to fix the adapter brackets and horizontal bars.

Installing the Adapter Brackets

4. Installing the Adapter Brackets

4-1 For Flat Back Screens

Adjust the brackets to fit mounting holes on the back side of the TV. Then tighten screws to fix the adapter brackets and horizontal bars.

Hooking the TV onto the Wall Mount

5. Hooking the TV onto the Wall Mount

4-2 For Recessed Back Screens or to Access A/V Inputs

• Level the TV.
• Place the lower thumbscrew; Tighten both thumbscrews. DO NOT OVER TIGHTEN SCREWS
• Screw the assembled bracket onto the TV.
• Position the assembled bracket as close as possible to the middle of the screen.

• Position the adapter brackets as close as possible to the center of the display.
• Screw the adapter brackets onto the TV.
• Tighten all screws but do not over tighten.
• Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

Adjustment

6. Adjustment

• Adjust to the desired position or tilt (wall: 180°, tilt: -15°, rotation: -2° ~ +2°).

Maintenance

• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please contact your distributor if you have any questions.

Legal & Compliance

Product identification

Model: PM-EASYFLEX-65 – manual version 1.0

Warranty and liability

The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.

The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.