← Products
PureMounts® TV-Wandhalterung - Move 23-42''
Discontinued

PM-MOVE-37A

PureMounts® TV-Wandhalterung - Move 23-42''

PureMounts® TV Wall Mount - Move 23-42''.

Manual
PDF / print
Chapter 1 of 7

Seite 1

Maintenance

  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).
  • Please contact your dealer if you have any questions.

37" MAX

100x100
200x100
200x200
2.5~20kg (5.5~44lbs)
2.5~20kg (5.5~44lbs)

ISSUED: OCT. 2012

Caution: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

SLIM FULL MOTION LED/LCD TV WALL MOUNT

INSTALLATION INSTRUCTIONS

PM-MOVE-37A

Chapter 2 of 7

Seite 2

Package M

Package W
ST6.3x55 (x3)
W-A
concrete anchor
W-B
(x3)

Note: Read the entire instruction manual before you start installation and assembly.

WARNING

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If any parts are missing or faulty, telephone your local distributor for a replacement.

  • Do not begin the installation until you have read and understood the instructions and warnings contained in this installation sheet. If you have any question regarding any of the instruction or warning, please contact your local distributor.
  • This mounting bracket was designed to be installed and utilized ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
  • This product should only be installed by someone of good mechanical ability, with basic building experience and fully understanding of this manual.
  • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
  • Always use assistant or mechanical lifting equipment to safely lift and position equipment.
  • Tighten screws firmly, but do not over tighten. Over tightening can damage the items, greatly reducing their holding power.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

articulated arm assembly
A
3mm (x1)
B
Allen key
6mm (x1)
C
Allen key
D8 (x4)
M-F
washerD (x4)
M-E
5 washer small spacer
M-G
(x8)
M5x14
M-B
(x4) M6x14
M-C
(x4) M8x20
M-D
(x4)M4x14
M-A
(x4)

Chapter 3 of 7

Seite 3

  • Remove the lower flat nut.
  • Loosen the upper nut, Remove VESA plate.

WARNING

3a. Mount on Wood Stud Wall

  1. Find and mark the exact location of mounting holes.
  2. Drill pilot holes
  3. Screw the wall mount onto the wall

2. Remove the Decorative Covers

1. Separate VESA Plate from Wall Mount

W-A
ø 4.5mm (ø 3/16")
55mm (2.2")
55mm (2.2")

X X√

  • Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
  • Installers are responsible to provide hardware for other types of mounting situations.
  • Installers must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
Chapter 4 of 7

Seite 4

4. Install Decorative Covers

5. Install VESA Plate

X X√

  • When installing wall mounts on cinder block, verify the actual concrete thickness is at least 1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
  • It is suggested electric drill on slow setting be used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
  • Installers must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

WARNING

3b. Mount on Solid Brick and Concrete Block

  1. Mark the exact location of mounting holes
  2. Drill pilot holes
  3. Screw the wall mount onto the wall

W-B
W-A
Top of TV
60mm (2.4")
60mm (2.4")
ø 10mm (ø 3/8")

Chapter 5 of 7

Seite 5

6. Hook the TV onto the Wall Mount

Loosen the upper nut spacing 4mm to VESA plate.
Hook the TV onto the wall mount

4mm

  • Tighten all screws but do not over tighten.
  • Screw VESA plate onto the TV.
  • Level the TV.
  • Place the lower flat nut and tighten both nuts.

or

TV
TVTV
TV
M-A/M-B
M-C/M-D
M-E
M-F
M-D
M-F
M-G
M-G
M-D
M-F
M-G

Chapter 6 of 7

Seite 6

7. Tension Adjust

8. Cable Management

Connect the cables to the display, and press cable cover inward to route the cables through the space.

Note: Leave slack in cable for cantilever arm movement. Adjust to the desired location or tilt.

height adjustable
max335mm

9. Adjustment

+15°

180°

+3° -3°

180°

Tighten screw till the display angle can be fixed.
B
Please keep the arm level during tension adjustment. Use a proper Allen key to slightly loosen or tighten the adjustment screw according to the display weight.
If display settles on its own, rotate adjustment screw towards the "+" symbol.
If display rises on its own, rotate adjustment screw towards the "-" symbol.
C
Please tighten socket set screw if the joints make popping sounds in use.

Was this helpful?
← PreviousNext chapter →
Staff sign-in