Page 1
PM-MOVE-52B 55"
Caution: Do not exceed the specified maximum weight to avoid serious damage.
Maintenance
You should check the tightness of the screws every two months. If you have any doubts about the installation, please contact your dealer or our customer service.
INSTALLATION MANUAL
Page 2
Note: Please read the entire installation manual carefully before beginning assembly and installation.
WARNING
- Do not begin installing your device before reading the installation manual and fully understanding the included instructions and warnings. If you have any questions, please contact your local dealer.
- Please adhere to the manufacturer’s recommended wall clearance to prevent possible damage.
- This product should only be installed by someone with good manual skills, basic construction experience, and a complete understanding of the instructions.
- Ensure the wall can safely support the total weight of the mount together with all attached components.
- Never exceed the permissible maximum weight.
- When mounting on walls with wood paneling or stud walls, make sure the screws are placed in the center of the cross braces. Use a stud finder if necessary.
- Do not lift or position heavy equipment alone; do so with two people or mechanical assistance.
- Tighten screws securely but do not over-tighten. Over-tightening can damage components and compromise the mounting.
- This product is intended for indoor use in your home. Outdoor use may cause damage and injury.
Component Checklist
IMPORTANT: Make sure you have received all components by comparing the delivery to the component checklist. If any parts are missing or defective, please contact your dealer for replacements.
| Component | |
|---|---|
| Articulated Arm A (x1) | 4mm Allen Wrench E (x1) |
| D5 Washer M-F (x4) | D8 Washer M-G (x4) |
| 6mm Allen Wrench F (x1) | VESA Adapter C (x2) |
| Wrench G (x1) | VESA Adapter D (x2) |
| Package M | Package W |
| Small Spacer (x8) M-H | Large Spacer (x4) M-I |
| Concrete Anchor W-B (x3) |
Page 3
1. Dismantling the VESA Plate from the Wall Mount
2. Removing the Cover Plates
- Loosen the upper nuts
- Then remove the lower nuts
- Remove the VESA plate
3a. Mounting on a Stud Wall or Wood Paneling
Caution: Ensure the screws are placed in the center of the cross braces. Use a stud finder if necessary.
For other wall types, the installer is responsible for procuring the correct installation materials (anchors, screws, etc.).
Please ensure the wall can safely support the total weight of the mount together with all attached components.
- Locate and mark the exact positions of the mounting holes.
- Drill the holes.
- Screw the wall mount to the wall.
Page 4
3b. Mounting on Solid Brick and Concrete Walls
- Locate and mark the exact positions of the mounting holes.
- Drill the holes.
- Screw the wall mount to the wall.
Please ensure the wall can safely support the total weight of the mount together with all attached components.
4. Attaching the Decorative Covers
5. Assembly of the VESA Mount
5a VESA 300x300, 400x400
5b VESA 400x200
Page 5
6. Mounting the VESA Plate 7. Installing the Display
Note: Select the appropriate screws, washers, and spacers (if required) according to the type of display.
- Screw the appropriate spacers onto your TV device
- Tighten all screws securely, but do not over-tighten.
- Position the VESA plate as close as possible to the center of the TV device.
- Loosen the upper nuts until there is approximately 4mm clearance to the wall mounting plate.
- Hang your TV device on the wall mount.
- Align your TV device as desired.
- Now secure the lower nuts and tighten all nuts.
6-1 For flat TV backs
6-2 For curved or recessed TV backs
Page 6
8. Adjusting the Tension
Please tighten the internal adjustment screw if creaking noises occur during use.
Please keep the arm height constant when adjusting the screw. Use the included Allen wrench to loosen or tighten the swivel arm tension according to your screen’s weight.
- If the screen lowers by itself without touching: Turn the screw towards + to increase tension.
- If the screen rises by itself without touching: Turn the screw towards - to decrease tension.
9. Cable Management
Connect the cables to your TV device. Route the cables along the swivel arms and press the cables into the corresponding channels to secure them in position.
Note: Leave some slack in the cables to avoid restricting the swivel arm’s range of motion.
10. Adjustment
Tighten the screws with the Allen key (or tighten the nuts) until the tilt angle can be fixed.
Set the desired position and tilt angle.
Legal & Compliance
Product identification
Model: PM-MOVE-52B – manual version 1.0
Warranty and liability
The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.
The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.
Trademarks and disclaimer
Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.
Packaging
Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.