Safety precautions
- Unpack the equipment carefully and save the original box and packing material for possible future shipment
- Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
- Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
- Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
- Refer all servicing to qualified service personnel.
- To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
- Do not put any heavy items on the extension cable in case of extrusion.
- Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards.
- Install the device in a place with fine ventilation to avoid damage caused by overheat.
- Keep the module away from liquids.
- Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
- Do not twist or pull by force ends of the optical cable. It can cause malfunction.
- Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
- Unplug the power cord when left unused for a long period of time.
- Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.
Product Introduction
Thanks for choosing Purelink PT-HDBT-1010, which consists of a transmitter and a receiver. It can extend 4K or 1080p video to distance up to 328 feet (100 meters) over a single CAT6A cable without compression. It supports audio de-embedding and ARC. It also supports bi-directional IR, USB and RS232 pass-through control and Ethernet extension. 24V PoC feature allows the transmitter and the receiver can be powered from each other and only one power adapter is needed in system.
Feature
- 18Gbps high bandwidth, HDMI V2.0.
- HDMI video resolution up to 4K@60Hz 4:4:4, HDR10, Dolby Vision.
- Supports HDCP bypass and HDCP 2.2 compliant.
- HDBaseT 3.0 solution which supports extending signal without compression.
- Extends 4K or 1080p video signals to distances up to 328 feet (100 meters) over a single SFTP CAT6A cable.
- Bi-directional IR, USB and RS232 pass-through control and Ethernet extension.
- Supports bi-directional 24V PoC.
- Supports audio de-embedding and ARC (Audio Return Channel).
- Provides HDMI loop out on transmitter.
Package List
- 1x PT-HDBT-1010-TX Transmitter
- 1x PT-HDBT-1010-RX Receiver
- 2x TX Mounting Ears with 2 Screws
- 2x RX Mounting Ears with 2 Screws
- 4x Plastic Cushion
- 4x Plastic Cushion
- 1x Power Adapter (24V DC 1.25A)
- 1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the components is found.
Panel Description
Transmitter Front Panel
| No. | Name | Description |
|---|---|---|
| ① | POWER LED | Illuminates green when power is applied, or blinks when in firmware upgrade mode. |
| ② | LINK LED | Illuminates when there is a valid HDBaseT link between the transmitter and the receiver. |
| ③ | HDCP LED | Illuminates when the video contains HDCP content, or blinks when the video has no HDCP content. |
| ④ | SOURCE LED | Illuminates when there is an HDMI source device is connected to HDMI input port. |
| ⑤ | LOOPOUT LED | Illuminates when both HDMI source device and HDMI display device (HDMI loop out port) are connected. |
| ⑥ | USB | DIP switch for DEVICE or HOST mode selection. DEVICE: The USB devices at transmitter position are used to control the HOST PC at receiver position. HOST: The HOST PC at transmitter position is controlled by the USB devices at receiver position. |
| ⑦ | DEVICE | Four type-A USB 2.0 ports for USB devices (e.g. Mouse, Keyboard and Camera) connection to control the PC which is connected to the HOST port of receiver. |
| ⑧ | HOST | Type-B USB 2.0 port for PC connection. The PC can be controlled by the USB devices which are connected to type-A USB 2.0 ports of receiver. |
Transmitter Rear Panel
| No. | Name | Description |
|---|---|---|
| ① | ETHERNET | Used for Ethernet extension together with the ETHERNET port of receiver. |
| ② | HDBT OUT | RJ45 port to connect the HDBT input port of receiver by CAT6A Ethernet cable. The LINK LED illuminates when there is a valid HDBaseT link between the transmitter and the receiver. The HDCP LED illuminates when the video contains HDCP content. |
| ③ | SOURCE | Connects to HDMI source device. |
| ④ | LOOPOUT | Connects to HDMI display device. |
| ⑤ | ARC OUT | Connects to audio player (e.g. amplifier) for ARC audio output. |
| ⑥ | AUDIO OUT | Connects to audio player (e.g. amplifier) for audio de-embedding from HDMI input. |
| ⑦ | IR IN | Connects to the IR receiver for IR pass-through. |
| ⑧ | IR OUT | Connects to the IR emitter for IR pass-through. |
| ⑨ | RS232 | Connects to RS232 control device (e.g. PC) or a third-party device for RS232 control. |
| ⑩ | FIRMWARE UPGRADE BUTTON | Press the button with paper clip or other sharp tool for 3s to enter firmware upgrade mode. Press the button for 3s again can exit the mode. |
| ⑪ | DC 24V | DC connector for the power adapter connection. |
Receiver Front Panel
| No. | Name | Description |
|---|---|---|
| ① | POWER LED | Illuminates green when power is applied, or blinks when in firmware upgrade mode. |
| ② | LINK LED | Illuminates when there is a valid HDBaseT link between the transmitter and the receiver. |
| ③ | HDCP LED | Illuminates when the video contains HDCP content, or blinks when the video has no HDCP content. |
| ④ | DISPLAY LED | Illuminates when there is a HDMI display device is connected to HDMI output port and when input source is detected. |
| ⑤ | ARC | DIP switch for ARC mode selection. HDMI: The ARC input via HDMI output port of receiver. PASS: Supports CEC & ARC pass-through. SPDIF: The ARC input via SPDIF input port of receiver. |
| ⑥ | USB | DIP switch for DEVICE or HOST mode selection. DEVICE: The USB devices at receiver position are used to control the HOST PC at transmitter position. HOST: The HOST PC at receiver position is controlled by the USB devices at transmitter position. |
| ⑦ | DEVICE | Four type-A USB 2.0 port for USB devices (e.g. Mouse, Keyboard and Camera) connection to control the PC which is connected to the HOST port of transmitter. |
| ⑧ | HOST | Type-B USB 2.0 ports for PC connection. The PC can be controlled by the USB devices which are connected to type-A USB 2.0 ports of transmitter. |
Receiver Rear Panel
| No. | Name | Description |
|---|---|---|
| ① | ETHERNET | Used for Ethernet extension together with the ETHERNET port of transmitter. |
| ② | HDBT IN | RJ45 port to connect the HDBT output port of transmitter by CAT6A Ethernet cable. The LINK LED illuminates when there is a valid HDBaseT link between the transmitter and the receiver. The HDCP LED illuminates when the video contains HDCP content. |
| ③ | DISPLAY | Connects to HDMI display device. |
| ④ | ARC IN | Connects to ARC audio source device (e.g.TV). |
| ⑤ | IR IN | Connects to the IR receiver for IR pass-through. |
| ⑥ | IR OUT | Connects to the IR emitter for IR pass-through. |
| ⑦ | RS232 | Connects to RS232 control device (e.g. PC) or a third-party device which is to be controlled. |
| ⑧ | FIRMWARE UPGRADE BUTTON | Press the button with paper clip or other sharp tool for 3s to enter firmware upgrade mode. Press the button for 3s again can exit the mode. |
| ⑨ | DC 24V | DC connector for the power adapter connection. |
Specification
| Transmitter | Receiver | |
|---|---|---|
| Video | ||
| Input | (1) SOURCE | (1) HDBT IN |
| Input Connector | (1) Type-A female HDMI | (1) RJ45 |
| Input Resolution | Up to 4K@60Hz 4:4:4 | Up to 4K@60Hz 4:4:4 |
| Output | (1) HDBT OUT, (1) LOOP OUT | (1) DISPLAY |
| Output Connector | (1) RJ45, (1) Type-A female HDMI | (1) Type-A female HDMI |
| Output Resolution | Up to 4K@60Hz 4:4:4 | Up to 4K@60Hz 4:4:4 |
| Audio | ||
| Input | - | (1) ARC IN |
| Input Connector | - | (1) Toslink Connector |
| Output | (1) ARC OUT, (1) AUDIO OUT | - |
| Output Connector | (1) Toslink connector (1) 3.5mm jack | - |
| Audio Format | Toslink (ARC): PCM, Dolby Digital, DTS 5.1CH 3.5mm Audio: PCM 2CH | |
| Frequency Response | 20Hz ~ 20KHz, ± 3dB | |
| Max Output Level | 2.0Vrms ± 0.5dB. 2V = 16dB headroom above -10dBV (316mV) nominal consumer line level signal | |
| THD+N | < 0.05% (-80dB), 20Hz~20KHz bandwidth, 1kHz sine at 0dBFS level (or max level) | |
| SNR | > 85dB, 20Hz-20kHz bandwidth | |
| Crosstalk Isolation | > 70dB, 10kHz sine at 0dBFS level (or max level before clipping) | |
| L-R Level Deviation | < 0.3dB, 1kHz sine at 0dBFS level (or max level before clipping) | |
| Frequency Response Deviation | < ± 0.5dB, 20Hz – 20kHz | |
| Output Load Capability | 1KΩ and higher (Supports 10x paralleled 10KΩ loads) | |
| Stereo Channel Separation | >70dB@1KHz | |
| Control | ||
| Control Part | (4) DEVICE, (1) HOST, (1) USB Switch, (1) IR IN, (1) IR OUT, (1) RS232, (1) ETHERNET | (4) DEVICE, (1) HOST, (1) ARC Switch, (1) USB Switch, (1) IR IN, (1) IR OUT, (1) RS232, (1) ETHERNET |
| Control Connector | (4) Type-A USB 2.0, (1) Type-B USB 2.0, (1) 2-pin DIP Switch, (2) 3.5mm Jacks, (1) 3-pin Terminal Block, (1) RJ45 | (4) Type-A USB 2.0, (1) Type-B USB 2.0, (2) 3-pin DIP Switch, (2) 3.5mm Jacks, (1) 3-pin Terminal Block, (1) RJ45 |
| General | ||
| Bandwidth | 18Gbps | |
| HDMI Standard | 2.0 | |
| HDCP Version | Input: HDCP 2.2, HDCP 1.4 compliant Loopout: Follows the display’s HDCP version. RX Output: Follows the source’s HDCP version. | |
| CEC | Pass-through (when ARC switch is selected to PASS or SPDIF) | |
| Bi-directional PoC | Supported | |
| HDMI V2.0 Cable Length | 4K@60Hz 4:4:4 ≤ 5m, 4K@60Hz 4:2:0 ≤ 15m, 1080P ≤ 20m | |
| Transmission Standard | HDBaseT | |
| Transmission Distance | 4K/1080p ≤ 262 feet (80 meters) | |
| Operation Temperature | -5 to +55℃ (+23° to +131°F) | |
| Storage Temperature | -25 to +70℃ (-13° to +158°F) | |
| Relative Humidity | 10% to 90%, Non-condensing | |
| Power Supply | Input:100V~240V AC; Output:24V DC 1.25A | |
| Power Consumption | 16.1W (Max) | |
| Dimension (W*H*D) | 200mm x 25mm x 100mm | |
| Net Weight | 290g |
Note: 1. Please use high-qualified HDMI cable fully compliant with HDMI V2.0 for reliable transmission and connection.
2. Suggest to use 80m for installation maximum, if 100m requires high quality SFTP CAT6A cable.
System Diagram
- When ARC switch is selected to HDMI, and the TV supports ARC, the TV audio can be transmitted back to the transmitter via HDMI output port of receiver, and then it will be output by the ARC OUT & HDMI Source port of transmitter. CEC pass-through is not supported in this mode.
- When ARC switch is selected to SPDIF, the audio can be transmitted back to the transmitter via ARC IN port of receiver, and then it will be output by the ARC OUT & HDMI Source port of transmitter. Besides, it also supports CEC pass-through in this mode.
- When ARC switch is selected to PASS, the extender can pass the ARC signal and support CEC pass-through. If the amplifier can work with the TV for ARC function, the ARC audio can be transmitted back to the transmitter via HDMI output port of receiver, and then it will be output by the ARC OUT & HDMI Source port of transmitter.
After-Sales Service
If there appear some problems when running the product, please check and deal with the problems referring to this user manual. Any transport costs are borne by the users during the warranty.
- Product Limited Warranty: This product will be free from defects in materials and workmanship for two years (The purchase invoice shall prevail). Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service.
- What the warranty does not cover (servicing available for a fee):
- Warranty expiration. Factory applied serial number has been altered or removed from the product. Damage, deterioration or malfunction caused by: Normal wear and tear. Use of supplies or parts not meeting our specifications. No certificate or invoice as the proof of warranty. The product model showed on the warranty card does not match with the model of the product for repairing or had been altered. Damage caused by force majeure. Servicing not authorized by distributor. Any other causes which does not relate to a product defect. Delivery, installation or labor charges for installation or setup of the product.
- Technical Support: For any questions or problems, contact your distributor or reseller and tell them the respective product name and version, the detailed failure situation as well as the formation of the cases.
Asking for Assistance
Technical Support
Phone: +49 5971 800299 - 0
Fax: +49 5971 800299 – 99
Technical Support Hours:
8:30 AM to 5:00 PM Monday thru Thursday
8:30 AM to 4:00 PM Friday
Write to:
PureLink GmbH
Von-Liebig-Straße 10
D - 48432 Rheine
www.purelink.de
info@purelink.de
Legal & Compliance
ManufacturerPureLink GmbHVon-Liebig-Str. 1048432 RheineGermanyPhone +49 5971 800299-0Fax +49 5971 800299-99info@purelink.dewww.purelink.deContact form: www.purelink.de/en/anfrage-formular-purelink.deUnited KingdomPureLink UK Ltd.Carpenter Court, 1 Maple RoadBramhall, StockportCheshire SK7 2DHUnited Kingdom
Product identification
Model: PT-HDBT-1010 – manual version 1.0
Trademarks and disclaimer
Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.
FCC
Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
Disposal of electrical and electronic equipment
WEEE reg. no.: DE 93847290
The crossed-out wheelie bin symbol on the product, packaging or in this manual means that electrical and electronic equipment must not be disposed of with household waste at the end of its life. Hand in old devices free of charge at a public collection point or return them to a distributor obliged to take them back. Remove batteries and lamps that can be removed without destroying the device before handing it in, and delete any personal data stored on the device. Details are regulated by national law. By returning old devices you help protect the environment.
Packaging
Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.