Safety precautions

To insure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference.

• Unpack the equipment carefully and save the original box and packing material for possible future shipment
• Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
• Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Do not put any heavy items on the extension cable in case of extrusion.
• Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards.
• Install the device in a place with fine ventilation to avoid damage caused by overheat.
• Keep the module away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
• Do not twist or pull by force ends of the optical cable. It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Unplug the power cord when left unused for a long period of time.
• Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.

Introduction

Introduction to PT-PSW-52

The PT-PSW-52 (hereinafter referred to as “Scaler Switcher”) is a compact mini scaler switcher with 5 video inputs (1 HDMI/MHL, 2 HDMI, 1 DP, and 1 VGA) and 3 audio inputs (1 DP external audio, 1 VGA auxiliary audio, 1 MIC audio). The VGA input supports VGA, YPbPr and C-video, so the device switcher is compliant with multiple video signals.
The Scaler Switcher scales & switches any video signal to HDMI output and HDBaseT output (supports PoH and connects to an HDBaseT Receiver, up to a maximum transmission distance of 70 meters.
With 1 IR IN, 1 IR OUT & 1 RS232, the IR & RS232 signals can be transmitted bi-directionally between the Scaler Switcher and the HDBaseT Receiver.
In addition, the Scaler Switcher can be controlled via front panel buttons, IR remote, RS232 commands and web-based GUI.

Feature

• Compliant with HDMI 1.3 & HDCP 2.2.
• Supports CEC, with commands to enable/disable this function.
• Supports video source auto-switching function.
• Bi-directional IR & RS232 control.
• Output resolutions selectable to assure preferred output, and supports various output resolutions, such as 1920x1200, 1920x1080, 1600x1200, 1600x900, 1360x768, 1280x800, 1280x720, 1024x768.
• VGA video supports C-video, YPbPr and VGA.
• 48V phantom power to support condenser microphone.
• MIC port supports balance/unbalance signal, suppress the external noise effectively.
• 3-level MIC input, supports condenser microphone, dynamic microphone and wireless microphone.
• Controllable via buttons, IR remote, RS232 & GUI.
• Powerful OSD function.
• Convenient firmware update port.

Package List

• 1 x PT-PSW-52 Compact Scaler Switcher
• 2 x Mounting Ears with 4 Screws
• 4 x Plastic Cushions
• 1 x Power Adapter (24VDC,2.71A)
• 1 x IR Remote
• 1 x IR Receiver (with carrier wave)
• 1 x IR Emitter
• 2 x 3-Pin Phoenix Connectors
• 1 x 5-Pin Phoenix Connector
• 1 x VGA Converting Cable (VGA to YPbPr)

Receiver

• 1 x PT-HDBT-702-RX HDBaseT Receiver
• 2 x Mounting Ears with 4 Screws
• 4 x Plastic Cushions
• 1 x User Manual

Note: Please confirm if the product and the accessories are all included, if not, please contact with the dealers.

Panel Description

Front Panel

• ① Built-in IR Receiver
• ② Power indicator
• ▪ Off when there is no power to the device.
• ▪ Red when the device is in standby mode.
• ▪ Green when the device is powered on.
• ③ 1-HDMI/MHL input Selector & Activity LED; Left key
• ④ 2-HDMI input Selector & Activity LED; Right key
• ⑤ 3-HDMI input Selector & Activity LED; Up key
• ⑥ 4-DisplayPort input Selector & Activity LED; Down key
• ⑦ 5-VGA input Selector Activity LED; Enter key
• ⑧ Auto-Switching Mode Selector& Activity LED; OSD menu button
• ▪ Press this button to enter or exit Auto-switching mode, in this mode, select input source via front panel button is not available, but RS232 command and IR remote are able to switch mode. The auto LED turn green and keep on.
• Note: When you set any VGA port to C-video or YPbPr in Manual-switching mode, the system will not be able to enter Auto-switching mode.
• ▪ Long-press this button more than 2 seconds to enter OSD menu, and then use ③~⑥ direction keys, ⑦ confirm key to control.

• ⑨ Volume Knob

Rear Panel

• ① INPUTS
• • Video input ports: 1 HDMI/MHL input, 2 HDMI inputs, 1 DP and 1 VGA
• • Audio input ports: 1 DP external audio input and 1 VGA auxiliary audio input.
• ② OUTPUTS
• • HDMI output: HDMI video output port
• • HDBaseT output: Support PoH. Connect with an HDBaseT Receiver to transmit AV signal or IR/RS232 control signal.
• HDBaseT output boasts green and yellow indicator. The green indicator will blink when power. If connect an HDBaseT receiver to this output successfully, the yellow indicator will light up, and the green indicator will keeps blinking.
• ③ MIC INPUT
• • MIC audio port: connect to Microphone.
• • Dial switch: including 3 level
• ✧ 48V phantom power mode (connect with condenser microphone);
• ✧ MIC mode (connect with dynamic microphone);
• ✧ LINE mode (connect with wireless microphone or line audio).

• ④ CONTROL
• ▪ RES RESET: press this button to reset the output resolution to 1280×720p, or activate HDMI and HDBT outputs when they are closed.
• ▪ IR IN: connect with IR receiver (with carrier wave only) to receive IR signal to control far-end device which was connected to HDBaseT Receiver via HDBaseT output port.
• ▪ IR OUT: connect with IR emitter to control local source devices from remote.
• ▪ IR EYE: connect with IR receiver (with carrier wave only) to receive IR signal send by IR remote to control this PT-PSW-52.
• ▪ FIRMWARE: Type-A USB port for updating system firmware or loading customized EDID data.
• ▪ RS232: Serial port, 3-pin phoenix connector, connect with a control device (such as PC) to control the PT-PSW-52 or other devices connected with HDBaseT Receiver.
• ▪ TCP/IP: Ethernet port, connect with PC to control the PT-PSW-52 via Web-based GUI.
• ⑤ AUDIO OUTPUT
• ▪ Audio output port, the audio comes from the input audio corresponding to the selected video source and is mixed with MIC audio.
• ⑥ DC 24V
• ▪ Power port, connect with DC 24V power adapter.

Note: Pictures shown in this manual are for reference only, different model and specifications are subject to real product.

System Connection

Usage Precaution

• System should be installed in a clean environment, preferably at ambient temperature or within given working temperature range (see page44 for limits).
• All of the power switches, plugs, sockets and power cords should be insulated.
• All devices should be connected before power on.

System Diagram

System connection diagram showing microphone, IR receiver, control system, router, laptop, speaker, pad, DVD, camera, TV, PT-HDBT-702-RX, with color-coded cables for VGA, HDMI, Audio, Control, HDBaset, IR Control.

Connection Procedure

1. Connect HDMI source devices (e.g. Blue-ray DVD) to 1~3 HDMI input ports with HDMI cable
2. Connect a DisplayPort source device (e.g. MAC MINI) to DP input port with DisplayPort cable and DP audio input port with audio cable.
3. Connect a VGA source device (e.g. Laptop) to VGA input port with VGA cable and VGA audio input port with audio cable.
4. Select MIC level and connect right microphone to MIC input port. MIC audio will be transmitted to AUDIO OUTPUT port and mixed with source audio.
5. Connect a HDMI display device to HDMI output port with HDMI cable.
6. Connect HDBaseT Receiver to HDBT output port with twisted pair.
7. Connect speaker, headphone or AV amplifier to AUDIO OUTPUT port.
8. Connect control device (e.g. PC, control system) to the TCP/IP port, the PT-PSW-52can be controlled via web-based GUI.
9. Connect control device (e.g. PC) to the RS232 port of the PT-PSW-52or the HDBaseT Receiver (bi-directional RS232 control, either end is available).
10. Connect IR receiver to the IR EYE port, the PT-PSW-52can be control via IR remote. For more details, please refer to 4.2.IR Control.
11. Both the PT-PSW-52and the HDBaseT Receiver have IR IN and OUT. When one model is connected with IR receiver, the other model should connect with an IR transmitter. For example: When “IR IN” of the PT-PSW-52connects with an IR receiver, the IR transmitter must connect to IR OUT of HDBaseT Receiver. The IR signal can be transmitted bi-directionally between the PT-PSW-52and the HDBaseT Receiver.
12. Connect DC24V power adaptor to the power port (HDBaseT Receiver can be powered by the PT-PSW-52with PoH function). Note: If the power adapter is connecting with HDBaseT Receiver, the PT-PSW-52 can’t be powered from HDBaseT Receiver.

3.3 Connection Procedure

1. Connect HDMI source devices (e.g. Blue-ray DVD) to 1~3 HDMI input ports with HDMI cable
2. Connect a DisplayPort source device (e.g. MAC MINI) to DP input port with DisplayPort cable and DP audio input port with audio cable.
3. Connect a VGA source device (e.g. Laptop) to VGA input port with VGA cable and VGA audio input port with audio cable.
4. Select MIC level and connect right microphone to MIC input port. MIC audio will be transmitted to AUDIO OUTPUT port and mixed with source audio.
5. Connect a HDMI display device to HDMI output port with HDMI cable.
6. Connect HDBaseT Receiver to HDBT output port with twisted pair.
7. Connect speaker, headphone or AV amplifier to AUDIO OUTPUT port.
8. Connect control device (e.g. PC, control system) to the TCP/IP port, the PT-PSW-52 can be controlled via web-based GUI.
9. Connect control device (e.g. PC) to the RS232 port of the PT-PSW-52 or the HDBaseT Receiver (bi-directional RS232 control, either end is available).
10. Connect IR receiver to the IR EYE port, the PT-PSW-52 can be control via IR remote. For more details, please refer to 4.2.IR Control.
11. Both the PT-PSW-52 and the HDBaseT Receiver have IR IN and OUT. When one model is connected with IR receiver, the other model should connect with an IR transmitter. For example: When “IR IN” of the PT-PSW-52 connects with an IR receiver, the IR transmitter must connect to IR OUT of HDBaseT Receiver. The IR signal can be transmitted bi-directionally between the PT-PSW-52 and the HDBaseT Receiver.
12. Connect DC24V power adaptor to the power port (HDBaseT Receiver can be powered by the PT-PSW-52 with PoH function).

Note: If the power adapter is connecting with HDBaseT Receiver, the PT-PSW-52 can’t be powered from HDBaseT Receiver.

Microphone Connection

The PT-PSW-52 provides with one 3-level microphone input port, to accommodate different microphone input modes, including 48V phantom power mode, MIC mode & LINE mode.

48V phantom power Mode

48V phantom power input has a good frequency characteristic, high input impedance and high sensitivity.
When switching to “48V”, the MIC input will provide a 48V phantom power. This is only used for condenser microphone.
Connect the microphone in this way: “+” connects to positive, “-” connects to negative and “⏚” to ground.
Switch to "48V" | Condenser Microphone

MIC Mode

MIC input has a low frequency characteristics, and wide frequency response.
When switch to “MIC”, the microphone input is used for connecting with dynamic microphone. There are two different connection methods:

1. Unbalanced connection: “+” and “⏚” connect to ground, and “-” connects to signal. “-” and “⏚” connect to ground, and “+” connects to signal.

Dynamic Microphone connection diagrams

1. Balanced connection: “+” connects to positive, “–” connects to negative and “ ” connects to ground.

Dynamic Microphone (Balanced connection) diagram

LINE Mode

LINE input has a low frequency characteristics, and wide frequency response.
When switch to “LINE”, the microphone input is used for connecting with line audio or wireless microphone output. There are two different connection methods:

1. Unbalanced connection: “+” and “ ” connect to ground, and “–” connects to signal.

1. “–” and “ ” connect to ground, and “+” connects to signal.

Switch to "LINE" line audio or wireless microphone

line audio or wireless microphone

Application

The PT-PSW-52 has a good application in various occasions, such as computer realm, monitoring, conference room, big screen displaying, television education, command & control center and smart home etc.

Button Control

Front panel buttons can be used for switching operations and volume adjusting.

Manual Switching

Press 1-HDMI/MHL, 2-HDMI, 3-HDMI, 4-DP, 5-VGA on front panel to select the corresponding input source.

Auto Switching

Press AUTO to enter in auto-switching mode.
The auto-switching mode abides by the following principles:

• New input Once detecting a new input signal, the switcher would switch to this new signal automatically.
• Rebooting device The PT-PSW-52 have the ability to save the last configuration before losing power. If the last switching mode is auto-switching, once rebooted, the switcher will automatically enter auto-switching mode, then detect all inputs and memorize their connection status for future rebooting using. If the last displayed signal is still available, the unit will output the signal. If not, the unit will detect all the input signals wit priority from 1-HDMI/MHL to 5-VGA. When detected the first signal, it will transfer to output.

Signal removing
Once removing the current display signal, the PT-PSW-52 will detect all input signals with priority from 1-HDMI/MHL to 5-VGA. It will transfer the signal firstly detected to be available to output devices.

Note: When the DP signal is switched as input, the DP source device may not read the EDID data from display device, at this point re-plug the DP source device to solve this phenomenon.Auto-switching function works only when inputting new signal, removing a signal or power rebooting. With any VGA port set to C-video or YPbPr, the system will be not able to enter in Auto-switching mode.

Volume Adjustment

Press Volume Knob to choose MIC/Source audio needed to be adjusted, the corresponding LED will turn green and keep on.Adjusting the Volume Knob in clockwise direction to increase sound volume.Adjusting the Volume Knob in anti-clockwise direction to decrease sound volume.

IR Control

IR Remote

Connect IR receiver to IR EYE port, the PT-PSW-52cans be controlled by using IR remote. As CEC function, it is able to use the IR remote to turn on/off the HDMI source or Display.
Scaler Switcher remote control illustration
Enter/ exit standby modeInput channel selection buttons(1~5): Select video source via pressing corresponding button (audio switched following the corresponding DP/VGA )Auto button: Enter/Exit auto-switching mode.Mute/ unmute audioVOL: Volume adjusting button. After pressing this button, the volume adjusting menu will be showed on Display, and then press UP/DOWON button to increase/decrease volume.OK: confirm button; Navigation buttons: UP/DWON/LEFT/ RIGHT button, for value setting or page-turn.

• Exit button: Exit OSD menu or current operation.
• Enter OSD menu or used to return to previous menu.

Control Far-end Device from Local

Connect an IR receiver to IR IN port on the PT-PSW-52 and connect IR emitter to the IR OUT port on the HDBaseT Receiver, the far-end device can be control by its IR remote from local.

HDBaseT signal routing and IR remote control setup diagram

Control Local Device from Remote

Connect an IR emitter to IR OUT port on the PT-PSW-52 and connect IR receiver to the IR IN port on the HDBaseT Receiver, the source devices can be control by their IR remote from remote.
HDBaseT Signal | Video Signal | IR Signal

CEC Function

The PT-PSW-52 supports CEC, it can be turned on/ off by sending RS232 commands or OSD menu operations. The default setting is ON.
Commands pertaining to CEC: 50686% (enable CEC) and 50687% (disable CEC)

HDMI INPUT ports 1~3 support CEC, if the connected source devices also support CEC and their CEC are on, users can control the source device and display via the IR remote of the PT-PSW-52.

IR Receiver and connections for HDMI input sources (DVD) and output (HDTV)

RS232 Control

As RS232 can be transmitted bi-directionally between the PT-PSW-52 and the HDBaseT Receiver, so it is able to control a third party RS232 device from local or control the PT-PSW-52 from remote. The baud rate support 2400, 4800, 9600 (default), 19200, 38400, 57600 or 115200.

RS232 Control Software

Here take the software docklight as an example.

• Installation Please download the latest Software Version from the link below: https://docklight.de/download/Docklight.zip Then follow the installation wizard for installation on Windows 7 and 10. After the installation, Docklight can be run for the first time and should look like the below screen shot: Registration is not necessary unless you wish to save settings on exit, so unless you wish to register click on "OK" to close the window.

Click "OK" to close this
The next pop-up window can also be closed with "Continue". An empty project is enough to send and receive commands easily (The default setting is always "Start with a blank project / blank script")

Click "Continue" to close this window.

Now you are in the main view, where commands are sent and feedback is received.
The next step is to select the correct COM port of the PC. To do this, double-click on "COM1" in the corresponding setup window.

Double click on "COM1" to change to the right COM port.
In the following window, select the drop-down menu labeled "Send / Receive on Comm Channel", select the appropriate COM port and then click on "OK" at the bottom right corner.
All other settings can be left at default for most applications, but refer to device RS232 settings to be sure.

Select the right COM port.

1. In order to be able to send commands, open communication with the device by clicking on "Play".
2. Then the keyboard function must be activated, so that commands can be written in the "communication window".
3. Finally enter the command, for example "50701%". This is then confirmed by pressing "Enter" to send. Any response from the connected device will appear in red.

User Manual

PT-PSW-52

1. Click "Play" to open the communication.
2. Enable the keyboard type in
3. Command sending area Monitoring area, indicates if the command sent works.

RS232 Command

Communication protocol: RS232 Communication Protocol
Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none

Switch Commands

Audio Commands

Resolution Commands

Setup Commands

Menu Commands

Inquire Commands

Adjustment Commands

CEC Commands

CEC Commands

RS232 Control Mode

Send ASCII command to control far-end third party device from the scaler switcher to receiver based on RS232 pass-through function.

• ① b = 0~6 is for baud rate.

• ② xxxxxxxx is for ASCII data (max 48 Byte).

/+1b:xxxx xxxxx

/+12:123456789

Send the ASCII command “123456789” to control the third party device of which baud rate is 9600.

RS232 Control Mode

Send HEX command to control the third party device from the scaler switcher to receiver based on RS232 pass-through function.

• ① b = 0~6 is for baud rate.

• ② xx xx xx xx is for HEX data (max 48 Byte).

/-12:30 31 32 33 34

Send the HEX command “30 31 32 33 34” to control the third party device of which baud rate is 9600.

Note: • Screen output adjusting avails only when the screen output adjusting is on. Send command 50678% to turn on.
• Under HDCP ON or HDCP OFF mode, the video signal can be switched to HDMI and HDBaseT output seamlessly, while sending 50791% to set as HDCP Active mode, the video signal can’t support seamless switching.

Control PT-PSW-52 or 3rd Party Device from Local

Firstly, according the following connection diagram to connect all devices as needed.

Secondly, send command 50787% (serial control mode 1, factory default) via RS232 communication software.

Lastly, send the right command of the PT-PSW-52 or other remote RS232 device connected in present system. Connect as below:
Control PT-PSW-52 or 3rd party device from local

Control PT-PSW-52 or 3rd Party Device form Remote

Secondly, send command 50788% via RS232 communication software.

Lastly, send the right command to control the PT-PSW-52. Connect as below:
Control PT-PSW-52 or 3rd party device from Remote

OSD Menu Control

The PT-PSW-52 provides a powerful OSD operation menu, contains 3 parts: optional settings, image settings, and system setting etc.
There are three ways to enter OSD menu:

• Long-press the button MENU/2s on front panel 2 seconds or more.
• Press MENU button on IR remote.
• Send the command 50616% on RS232 Control Software.

Operation:

• Press direction buttons on front panel or IR remote to switch between menu options and menu pages.
• Press ENTER on front panel or OK on the IR remote to confirm the selection.

OPTIONS

Includes Output Adjust, Input 5 Select, Baud rate, User EDID Load (USB), Resolution, and Software Update (USB).

OPTIONS menu screen with list of items

• Output Adjust: Adjust output image position (X: horizontal direction and Y: vertical direction), ratio aspect (width and height), polarity adjustment (H Polarity and V Polarity) and output setting (HDMI on/off and HDBT on/off).
• Input5 Select: Select video source format for VGA input, includes AV 1 (C-video signal), VGA 1 (VGA signal) and YPbPr 1 (Component video signal).
• Baud rate: Set the baud rate for RS232 control, and it support 2400, 4800, 9600, 19200, 38400, 57600, 115200.
• User EDID Load (USB): Insert the USB flash disk with EDID file to FIRMWARE port to load EDID data through this menu.
• Resolution: Set the output resolutions, and it support 1920x1200, 1920x1080, 1600x1200, 1600x900, 1360x768, 1280x800, 1280x720, 1024x768.

• Pw Off Time (Auto): Set the auto power off time when no signal input (1, 2, 5 or 10 minutes can be chosen).

• Pw Off Time (Manual): Set the power off time when no signal input (1, 2, 5 or 10 minutes can be chosen).
• IP: Show the IP address.
• Software Update (USB): Insert the USB flash disk with updating file to USB port of the PT-PSW-52, to update the software through this menu.

PICTURE

Including Picture Mode, Color Temperature, Aspect Ratio, Noise Reduction, Screen and Color Range.
Please check the picture below:

PICTURE | Picture Mode Standard / Color Temperature / Aspect Ratio / Noise Reduction / Screen / Color Range 16~235

• Picture mode: Include Dynamic, Standard, Mild, and User. Only in User mode, will it be able to set the image contrast, brightness, color and sharpness.
• Color Temperature: Include Cool, Medium, Warm and User. And only in User mode, it is able to set values for Red, Green and Blue (RGB).
• Aspect Ratio: Include Native, 4:3, 16:9, Zoom1, Zoom2, Just Scan, and Panorama. VGA format only supports 4:3, 16:9 and Panorama.
• Noise Reduction (not for VGA format): Includes Off, Low, Middle, High and Default.
• Screen: (not for HDMI source): Include Auto Adjust, Horizontal, Vertical, Size, and Phase.

SETUP

Including OSD Language, Restore Factory Default, Blending, HDMI CEC, OSD Duration and version inquiry
OSD setup screen

• OSD Language: Supports 7 languages, including English (default), Chinese etc.
• Restore Factory Default: Restores to original system state.
• Blending: Includes Low, Middle, High and Off.

• HDMI CEC: Enable/disable CEC and auto-standby function. Default: CEC on, STANDBY on. Only when CEC is on, will it be able to set auto-standby status.
• OSD Duration: Includes 5 Sec, 10 Sec, 15 Sec and Off.
• VERSION: Displays software version

GUI Control

In addition to control the PT-PSW-52 via front panel button, IR remote and RS232 communication software. The PT-PSW-52 can be controlled via web-based GUI. It allows users to interact with the PT-PSW-52 through graphical icons and visual indicators.
Type 192.168.0.178 in your browser, it will enter the log-in interface shown as below:

Control Menu

Type user name: user and password: user (default setting) on the log-in interface, and then click Login to enter Control menu shown as below:

• Sources: Click the corresponding button (1-HDMI/MHL, 2-HDMI, 3-HDMI, 4-DP, and 5-VGA) to select video input source.
• VGA: Click Adjust to adjust the position of VGA video output image to make sure the best visual effect.
• DP: Click Audio to turn on/off the DP external audio input.
• Volume: Click the corresponding positive/negative button to increase/decrease the volume of microphone audio or source audio input. Click the corresponding Mute button to mute/unmute microphone audio or source audio input.
• Click Source to turn on/off input source device.
• Click Display to turn on/off output display device.

• Click Local to let the PT-PSW-52r into standby mode.

Configuration Menu

① Click on control menu to enter setting menu shown as below:

• Output Resolution: Select the output resolution that you need and then click Confirm.
• Update: Insert the USB flash disk with EDID file/software updating file to FIRMWARE port, and then click EDID/Firmware to start update procedure.

• Shutdown Timer(NO Input): Set the shutdown time under manual-switching mode or auto-switching mode, including none, 1 minute, 2 minutes, 5 minutes and 10 Minutes. If the PT-PSW-52 can’t detect video source input, it will automatically shut down after a preset interval.

② Click Network to enter network setting menu shown as below:
Network setting menu interface
In this interface, dynamic or static IP mode can be selected. Under static IP mode, IP address and subnet mask, gateway can be set and make sure the IP addresses are different to avoid IP conflict.

③ Click Source Label to enter source label setting menu shown as below:
In this interface, the name of source input selection button can be modified as you need.

RS232 Control Menu

Click RS232 Control on the top of interface to enter RS232 control menu shown as below:
RS232 control menu interface screenshot

• Port: Local port refers to the RS232 port of the PT-PSW-52, and the HDBT port refers to the RS232 port of HDBaseT Receiver.
• Baud Rate: The baud rate of local port is 9600 which can’t be modified, but for HDBT port, it support 2400, 4800, 9600, 19200, 38400, 57600, 115200.

• Command: Typing commands in this box to control the PT-PSW-52 or the far-end device which is connected to HDBaseT Receiver. If checked the “Hex”, you can enter hexadecimal value in the “Command” box.

Password Menu

Click Password on the top of interface to enter password menu shown as below:

In this interface, the user name and password can be modified as you need.

GUI Update

GUI for the PT-PSW-52 supports online update in http://192.168.0.178:100. Type the username and password (the same as the GUI log-in settings, modified password will be available only after rebooting) to log in the configuration interface. After that, click Administration at the source menu to get to Upload Program as shown below:

Select the desired update file and press Apply, it will start upgrading then.

Specification

Panel Drawing

Troubleshooting & Maintenance

If your problem persists after following the above troubleshooting steps, seek further help from authorized dealer or our technical support.

After-Sales Service

If there appear some problems when running the product, please check and deal with the problems referring to this user manual. Any transport costs are borne by the users during the warranty.

1. Product Limited Warranty: This product will be free from defects in materials and workmanship for two years (The purchase invoice shall prevail). Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service.
2. What the warranty does not cover (servicing available for a fee):
3. Warranty expiration. Factory applied serial number has been altered or removed from the product. Damage, deterioration or malfunction caused by: Normal wear and tear. Use of supplies or parts not meeting our specifications. No certificate or invoice as the proof of warranty. The product model showed on the warranty card does not match with the model of the product for repairing or had been altered. Damage caused by force majeure. Servicing not authorized by distributor. Any other causes which does not relate to a product defect. Delivery, installation or labor charges for installation or setup of the product.
4. Technical Support: For any questions or problems, contact your distributor or reseller and tell them the respective product name and version, the detailed failure situation as well as the formation of the cases.

Legal & Compliance

Product identification

Model: PT-PSW-52 – manual version 1.0

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

EU conformity

PureLink hereby declares that this product PureTools PT-PSW-52 complies with Directives 1907/2006/EU und 2011/65/EU. PureLink GmbH hereby declares that this product PureTools PT-PSW-52 complies with Directives 2014/30/EU and 2014/35/EU.

The full text of the EU Declaration of Conformity is available at: http://www.purelink.de/ce/4260134127967_CE.pdf

Disposal of electrical and electronic equipment

WEEE reg. no.: DE 93847290

The crossed-out wheelie bin symbol on the product, packaging or in this manual means that electrical and electronic equipment must not be disposed of with household waste at the end of its life. Hand in old devices free of charge at a public collection point or return them to a distributor obliged to take them back. Remove batteries and lamps that can be removed without destroying the device before handing it in, and delete any personal data stored on the device. Details are regulated by national law. By returning old devices you help protect the environment.

Batteries

Batteries must not be disposed of with household waste. Return used batteries free of charge to collection points or retailers.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.