Safety precautions

To insure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference.

• Unpack the equipment carefully and save the original box and packing material for possible future shipment
• Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
• Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Do not put any heavy items on the extension cable in case of extrusion.
• Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards.
• Install the device in a place with fine ventilation to avoid damage caused by overheat.
• Keep the module away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
• Do not twist or pull by force ends of the optical cable. It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Unplug the power cord when left unused for a long period of time.
• Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.

Introduction to PT-PSW-61

The PT-PSW-61 is a compact 6x1 mini unit with 6 video inputs (4 HDMI, 2 VGA), 2 auxiliary audio inputs (switched following VGA), 1 HDMI output and 3 audio outputs (1 dual-mono analog audio, 1 3.5mm stereo audio, 1 optical audio). The PT-PSW-61 switches VGA or HDMI/DVI input signal to HDMI output. Besides, the unit up-scales VGA to HDMI output and supports resolution adjustment (6 types in total). It bypass HDMI and provides comprehensive resolution capacities up to 4K& 1080p 3D. The unit also supports RS232&IR control and EDID management.

Feature

• Control -- via Front panel buttons, RS232 commands and IR Remote
• Switch -- select 6 input source to HDMI output
• Scale – scale VGA to HDMI output, Output resolutions selectable to assure preferred output, and supports various output resolutions, such as 1920x1200, 1920x1080, 1360x768, 1280x800, 1024x768, 1280x720
• Support HDMI 1.4, 4Kx2K&1080P 3D, compliance with HDCP1.4
• Transmit 4Kx2K signal up to 15m.
• Support EDID management
• Two input switching modes: auto-switching or manual-switching
• Intuitive indicator for power connect states & source selection & output resolution selection
• Support audio & video output management via OUTPUT BLACK button.
• Support online software upgrading
• Compact design for easy operation
• Support power-off memory
• Support hot plug

Package List

• 1 x PT-PSW-61
• 2 x Mounting Ears
• 4 x Screws
• 4 x Plastic Cushions
• 1 x Power Adapter (DC 5V 3A)
• 2 x 3-pin Pluggable Terminal Blocks (pitch:3.81mm)
• 1 x IR Receiver
• 1 x IR Remote (Cell battery is not included)
• 1 x User Manual

Note: Confirm if the product and the accessories are all included, if not, please contact with your dealers.

Front Panel

Note: Pictures shown in this manual are for reference only, different model and specifications are subject to real product.

Rear Panel

Usage Precaution

• System should be installed in a clean environment, preferably at ambient temperature or within given working temperature range (see page 19 for limits).
• All of the power switches, plugs, sockets and power cords should be insulated.
• All devices should be connected before power on.

System Diagram

Speaker DVD Laptop HDTV Central Control System Remote
HDMI:
VGA:
RS232:
IR Control:
Audio:

Connection Procedure

1. Connect HDMI/DVI sources (e.g. DVD) to HDMI input ports of PT-PSW-61 with HDMI cables.
2. Connect VGA sources (e.g. DV Camera) to VGA input ports of PT-PSW-61 with VGA cables.
3. Connect sources to the AUDIO input ports of PT-PSW-61 with audio cables.
4. Connect a HDMI display (e.g. HDTV) to HDMI output port of PT-PSW-61.
5. Connect audio amplifiers (e.g. speaker/earphone) to audio outputs of PT-PSW-61.
6. Connect a control device (e.g. PC) to the RS232 port of PT-PSW-61.
7. Connect an IR Receiver（working voltage:5V）to the IR IN port of PT-PSW-61.
8. Plug DC 5V 3A power adapter to PT-PSW-61.

Application

PT-PSW-61 has a good application in various occasions, such as computer realm, monitoring, conference room, big screen displaying, television education, command & control center and smart home etc.

3.3 Connection Procedure

1. Connect HDMI/DVI sources (e.g. DVD) to HDMI input ports of PT-PSW-61 with HDMI cables.
2. Connect VGA sources (e.g. DV Camera) to VGA input ports of PT-PSW-61 with VGA cables.
3. Connect sources to the AUDIO input ports of PT-PSW-61 with audio cables.
4. Connect a HDMI display (e.g. HDTV) to HDMI output port of PT-PSW-61.
5. Connect audio amplifiers (e.g. speaker/earphone) to audio outputs of PT-PSW-61.
6. Connect a control device (e.g. PC) to the RS232 port of PT-PSW-61.
7. Connect an IR Receiver（working voltage:5V）to the IR IN port of PT-PSW-61.
8. Plug DC 5V 3A power adapter to PT-PSW-61.

3.4 Application

PT-PSW-61 has a good application in various occasions, such as computer realm, monitoring, conference room, big screen displaying, television education, command & control center and smart home etc.

Button Control

Front panel buttons can be used for source selections, output resolution adjusting, front panel buttons management, software updating and output screen setting. (Please refer to chapter 2.1 ).

Here is the detail information for source selections:
There are 6 sources for choose in total, including HDMI1, HDMI2, HDMI3, HDMI4, VGA1, VGA2. Video signals support auto-switching and manual-switching (factory default). Press and hold for SOURCE/AUTO for 3 seconds or more to enter in auto-switching/manual-switching mode.

Manual-switching

Dial ◀ to select the previous source, dial ▶ to select the next source.

Auto-switching

In this mode, select input source via front panel button (◀ ▶) is not available, but RS232 command and IR remote are able to switch mode. The auto LED turn green and keep on.

The auto-switching mode abides by the following principles:

• New input principle: Once detecting a new input signal, PT-PSW-61 would switch to this new signal automatically.
• Rebooting device principle: PT-PSW-61 have the ability of power-off memory. If the last switching mode is auto-switching, once rebooted, PT-PSW-61 will automatically enter auto-switching mode, and then detect all inputs and memorize their connection status for future rebooting using. If the last displayed signal is still available, PT-PSW-61 will output the signal. If not, the unit will detect all the inputs signals with priority from HDMI1 to VGA2. When detected the first signal, it will transfer to output.
• Signal removing principle: Once removing the current display signal, PT-PSW-61 will detect all input signals with priority from HDMI1 to VGA2. It will transfer the signal firstly detected to be available to output devices.

Operation Examples

• Connect HDMI2, HDMI4, and VGA2 ports with source devices, select HDMI4 to outputs.
• Press and hold for the front button SOURCE/AUTO for 3 seconds or more to enter in auto-switching mode.
• Connect HDMI3 with a source device, and then it will choose HDMI3 to output.
• Remove the signal of HDMI3, PT-PSW-61 will detect from HDMI1 to VGA2. And when it detects that HDMI2 is available, it will choose HDMI2 to output.
• Cut off the power of PT-PSW-61, then reboot. As the unit is in auto-switching mode, it will choose HDMI2 to output.

RS232 Control

Control Software

• Installation: Copy the control software file to the computer connected with PT-PSW-61.
• Uninstallation: Delete all the control software files in corresponding file path.

Basic Setting:
Firstly, connect PT-PSW-61 with an input device and an output device. Then, connect it with a computer which is installed with RS232 control software. Double-click the software icon to run this software. The icon is showed as below:

The interface of the control software is showed as below:
Please set the parameters of COM number, bound rate, data bit, stop bit and the parity bit correctly, only then will you be able to send command in Command Sending Area.

Monitoring area, indicates whether the command sent works.
Command Sending area

RS232 Command

Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none

Resolution Select Commands for VGA Input

Setup Commands

Switch to VGA2

Inquire Commands

Adjustment Commands for VGA input

Note: EDID commands are for HDMI sources only.The procedure of upgrading EDID data for user:Copy the file( the file must be named EDID.bin) to the root directory of a USB flash disk.Plug the USB flash disk to the PT-PSW-61 Firmware port on its rear panel.Send command 50769% to read EDID data from U flash disk, then, send command 50787% to update EDID.

IR Control

The unit enables to use the IR remote to control it. Here is brief description of IR remote.

• ① Standby button: Enter/exit standby mode.
• ② Input channel selection buttons: Selection video source via pressing corresponding button (audio switched following the corresponding VGA).
• ③ Auto button: Enter/exit auto-switching mode.
• ④ Resolution selection buttons: Select resolution via pressing corresponding button.
• ⑤ Output black button: Press to switch on/off Audio & Video output

1920x1080 1360x768 HDMI 1 1920x1200 1280x800 1024x768 VGA 1 HDMI 2 HDMI 3 HDMI 4 1280x720 Scaler Switcher VGA 2 INPUT SOURCE AUTO OUTPUT BLACK RESOLUTION ① ② ③ ④ ⑤

Firmware Updating

PT-PSW-61 supports firmware updating via USB flash disk. The procedures as follows:

1. Copy the file “MERGE.bin” to the root directory of a USB flash disk. (Make sure the file is copied to the root directory for normal use. The “MERGE.bin” file is provided/authorized.
2. Plug the USB flash disk to FIRMWARE port on its rear panel.
3. Press the button “RESOLUTION/FW UPDATE” for 7 seconds or more to update the firmware automatically. Or send command 50698% to update software.

Specification

Video

Audio

Control part

General

Note: PT-PSW-61 supports 4k&1080p 3D HDMI signal, please adopt quality HDMI cables compliant with HDMI1.4 for reliable transmission when connecting.

Panel Drawing

110 mm
347 mm
28.0 mm

Troubleshooting & Maintenance

Note: If your problem persists after following the above troubleshooting steps, seek further help from authorized dealer or our technical support.

After-Sales Service

If there appear some problems when running the product, please check and deal with the problems referring to this user manual. Any transport costs are borne by the users during the warranty.

1. Product Limited Warranty: This product will be free from defects in materials and workmanship for two years (The purchase invoice shall prevail). Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service.
2. What the warranty does not cover (servicing available for a fee):

• Warranty expiration.
• Factory applied serial number has been altered or removed from the product.
• Damage, deterioration or malfunction caused by:
• Normal wear and tear.
• Use of supplies or parts not meeting our specifications.
• No certificate or invoice as the proof of warranty.
• The product model showed on the warranty card does not match with the model of the product for repairing or had been altered.
• Damage caused by force majeure.
• Servicing not authorized by distributor.
• Any other causes which does not relate to a product defect.
• Delivery, installation or labor charges for installation or setup of the product.

1. Technical Support: For any questions or problems, contact your distributor or reseller and tell them the respective product name and version, the detailed failure situation as well as the formation of the cases.

Asking for Assistance

Technical Support:
Phone: +49 5971 800299 - 0
Fax: +49 5971 800299 – 99

Technical Support Hours:
8:30 AM to 5:00 PM Monday thru Thursday
8:30 AM to 4:00 PM Friday

Write to:
PureLink GmbH
Von-Liebig-Straße 10
D - 48432 Rheine
www.purelink.de
info@purelink.de

Legal & Compliance

Product identification

Model: PT-PSW-61 – manual version 1.0

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

FCC

Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.

Disposal of electrical and electronic equipment

WEEE reg. no.: DE 93847290

The crossed-out wheelie bin symbol on the product, packaging or in this manual means that electrical and electronic equipment must not be disposed of with household waste at the end of its life. Hand in old devices free of charge at a public collection point or return them to a distributor obliged to take them back. Remove batteries and lamps that can be removed without destroying the device before handing it in, and delete any personal data stored on the device. Details are regulated by national law. By returning old devices you help protect the environment.

Batteries

Batteries must not be disposed of with household waste. Return used batteries free of charge to collection points or retailers.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.