页 1
Video Wall Stand & Cart and Accessories INSTALLATION MANUAL
Caution: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
200x200/300x300 400x200/400x400
600x400
PDS-2302S 55"
MAX 60kgx2 (132lbsx2) RATED
60kgx2 (132lbsx2) RATED
PDS-2302C 55"
MAX 200x200/300x300 400x200/400x400 600x400
Maintenance
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
- Please contact your distributor if you have any questions.
Optional Accessories
Note: The accessories are not standard equipped. The accessories will be selected according to user requirement.
Note: The displays are installed by the numerical order given.
Note: The angle of displays are adjusted by the numerical order given.
页 2
WARNING
Note: Read the entire instruction manual before you start installation and assembly.
- Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
- This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
- Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
- Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
| Component | Quantity |
|---|---|
| Package M | x2 |
| washer | |
| M-F | x4 |
| M8x20 | |
| M-C | x4 |
| M5x14 | |
| M-A | x4 |
| M6x14 | |
| M-B | x4 |
| big spacer | x4 |
| M-H | M6x30 |
| M-D | x4 |
| M8x30 | |
| M-E | x4 |
| small spacer | x8 |
| M-G | |
| connecting piece | x1 |
| J | |
| top cover | x1 |
| K | |
| 3mm Allen key | x1 |
| P | |
| M8x40 | x4 |
| O | |
| column | x1 |
| I | |
| 5mm Allen key | x1 |
| R | |
| 6mm Allen key | x1 |
| S | |
| M8x16 | x4 |
| N | |
| M8x65 | x8 |
| M | |
| cable clamp | x8 |
| L | |
| D8 washer | x4 |
| T |
Component (PDS-2302C/PDS-2302S)
| Component | Quantity |
|---|---|
| middle base | x1 |
| A | |
| left cover | D(x1) right cover(x1) E |
| adapter bracket | G(x4) |
| left base | B(x1) right base C(x1) |
| universal plate | x2 |
| F | |
| connecting fitting | x2 |
| H |
Component (PDS-2302C only)
| Component | Quantity |
|---|---|
| supporting foot | x4 |
| Xcaster wheel/brake | U(x2) caster wheel V(x2) |
| wrench | x1 |
| W |
Component (PDS-2302S only)
| Component | Quantity |
|---|---|
| rubber pad | x4 |
| Y |
Note: (Peel off the backing paper from the rubber pad and stick the rubber pad on to the supporting foot.)
PDS-9501 (The following accessories are optional)
| Component | Quantity |
|---|---|
| power socket | x1 |
| T-H | |
| ST4.8x9.5 | x4 |
| P-G | |
| 4mm Allen key | x1 |
| Q |
页 3
1. Assembling the Base
Attach the left and right base to the middle base using the appropriate screws. Tighten all screws with an Allen key.
2. For the model PDS-9501 installation
Note: Assembly based on the accessories selected by user.
3. Attaching the Column to the Base
Attach the power socket to the back of column using the appropriate screws. Tighten all screws with a phillips screwdriver. Attach the column to the assembled base using the connecting piece, secure them with the appropriate screws.
Note: Lock the brakes on the casters to avoid any sudden movements during installation.
4. Installing the Covers
5. Installing the Universal Plates
Insert the universal plates to the column along the column rails respectively.
Note: With the arrow pointing upward.
Note: With the brake wheels facing forward.
页 4
7. Installing the Adapter Brackets
7-1 For Flat Back Screens
Top of the display
M-A/M-B/M-C M-F
6. Installing the Top Cover
Attach the top cover to the column using the appropriate screws. Tighten all screws with an Allen key.
X+5mm (X=Height of display)
Tighten all screws to secure them with an Allen key.
页 5
7-2 For Recessed Back Screens or to Access A/V Inputs
Tighten all screws but do not over tighten.
- Position the adapter brackets as close as possible to the center of the displays.
- Screw the adapter brackets onto the displays.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screens.
M-D/M-E M-F M-G M-H M-H M-D/M-E M-F M-G M-F M-C M-D/M-E/M-C M-F M-G or or or
8. Hanging the Displays onto the Universal Plates
- Lift the display carefully and pull downward two straps at the same time , then hook the adapter brackets to the universal plate. Fasten the adapter brackets to the universal plate by releasing the straps.
- The other display is hung onto the universal plate in the same way.
Note: If the displays uptilted, rotate the adjustment screws as shown in figure.
Note: Adjust the angle of displays by the numerical order given.
Note: Use the padlocks to prevent the displays from being stolen (The padlocks are not included).
9. Micro-Adjustment
Note: The displays are installed to the universal plates from the bottom up.
页 6
10. Cable Management
Insert the cable clamps horizontally into the plate slots, then turn the cable clamps to the vertical to secure them.
Run the cables through the cable clamps and the rubber strip.
Note: If the displays tilted down, rotate the adjustment screws as shown in figure.
Note: Rotate the adjustment screws as shown in figure to make a one millimeter gap left between the upper and lower displays.
页 7
12. Multi-screen Combination Solution
11. Adjustment
+3° -3°
- Loosen the screws in the plastic covers in order to remove the plastic covers.
- Remove the screws attaching the front of the universal plates.
- Connecting attachment
- Loosen the screws in the connecting fittings in order to slide the connecting attachments to both sides of the connecting fittings. Then tighten all screws to secure.
页 8
13. Cable Management
or
X+5mm (X=Height of display)
Insert the connecting fittings to the appropriate position along the universal plates rails.
Note: Make sure that the universal plates are at the same level with each other.
Smaller display Larger display
Use the connecting fittings to assemble the other cart (or stand) .
Note: Make sure that the carts (or stands) are in alignment.
Tighten all screws to secure them.
Note: The position which the connecting fittings insert to the universal plate is determined by the size of displays.
1mm Note: Leave a one millimeter gap between both displays.
Note: The angle of displays are adjusted by the numerical order given.
Note: The displays are installed by the numerical order given.
Legal & Compliance
Product identification
Model: PDS-2302C – manual version 1.0
Warranty and liability
The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.
The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.
Trademarks and disclaimer
Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.
Packaging
Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.