页 1
11. Cable Management
Caution: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
200x200/300x300
400x200/400x400
600x400
PDS-2304S 55"
MAX 60kgx4 (132lbsx4)
RATED 60kgx4 (132lbsx4) RATED
PDS-2304C 55"
MAX 200x200/300x300
400x200/400x400
600x400
Maintenance
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
- Please contact your distributor if you have any questions.
Insert the cable clamps horizontally into the plate slots, then turn the cable clamps to the vertical to secure them.
Run the cables through the cable clamps and the rubber strip.
PDS-9501
Note: The accessories are not standard equipped. The accessories will be selected according to user requirement.
Optional Accessories
页 2
Caution: Read the entire instruction manual before you start installation and assembly.
- Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
- This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
- Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
- Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items. This greatly reduces their holding power.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
PDS-2304C/PDS-2304S
| Component | Description | Qty |
|---|---|---|
| M-F | washer | 4 |
| M-C | M5x14 | 4 |
| M-A | M6x14 | 4 |
| M-B | (big spacer) | 4 |
| M-H | M6x30 | 4 |
| M-D | M8x30 | 4 |
| M-E | (small spacer) | 8 |
| M-G |
| Component | Model | Qty | Description |
|---|---|---|---|
| W | PDS-2304C only | 2 | caster wheel/brake |
| X | PDS-2304C only | 2 | caster wheel |
| Y | PDS-2304C only | 1 | wrench |
| M | PDS-2304S only | 2 | connecting piece |
| N | PDS-2304S only | 2 | top cover |
| S | PDS-2304S only | 1 | 3mm Allen key |
| R | PDS-2304S only | 8 | M8x40 |
| K | 2 | column | |
| T | 1 | 5mm Allen key | |
| U | 1 | 6mm Allen key | |
| Q | PDS-2304S only | 8 | M8x16 |
| P | PDS-2304S only | 8 | M8x65 |
| O | 16 | cable clamp | |
| V | PDS-2304S only | 8 | D8 washer |
| L | 2 | M6x20 | |
| D | 1 | left cover | |
| E | 1 | right cover | |
| A | 1 | middle base | |
| B | 1 | left base | |
| C | 1 | right base |
PDS-9501 The following accessories are optional
| Component | Description | Qty |
|---|---|---|
| power socket | 2 | |
| T-H ST4.8x9.5 | 8 | |
| P-G | adapter bracket | 8 |
| G | universal plate | 2 |
| F | support plate | 4 |
| J | plastic cover | 4 |
| H | supporting foot | 4 |
| Z | rubber pad | 4 |
| A1 | Peel off the backing paper from the rubber pad and stick the rubber pad on to the supporting foot. | |
| ST4.2x9.5 | 8 | |
| I |
页 3
Attach the left and right base to the middle base using the appropriate screws. Tighten all screws with an Allen key.
2. For the model PDS-9501 installation
(Assembly based on the accessories selected by user.)
3. Attaching the Columns to the Base
Attach the power sockets to the back of columns using the appropriate screws. Tighten all screws with a phillips screwdriver.
Attach the columns to the assembled base using the connecting pieces, secure them with the appropriate screws.
Note: Lock the brakes on the casters to avoid any sudden movements during installation.
T-H U P M R U V
4. Installing the Covers
D E
5. Installing the Support Plates
P-G T
Insert the support plates into the columns along the column rails respectively.
Keep the support plates at the same level.
Tighten all screws to secure the support plate.
With the arrow pointing up.
A B C
Note: With the brake wheels facing forward.
1. Assembling the Base
X+5mm
(X=Height of display)
页 4
7. Installing the Top Covers
6. Installing the Universal Plates
U Q N
Attach the top covers to the columns using the appropriate screws. Tighten all screws with an Allen key.
8. Installing the Adapter Brackets
Top of the display
L I
Insert the universal plates to the support plates and align the holes in the universal plates with the holes in the support plates.
- Attach the two plastic covers to both ends of the universal plates using the screws and tighten all screws to secure.
- The other two plastic covers are installed in the same way.
- Tighten all screws but do not over tighten!
- Install the screw into either of two holes.
H
页 5
8-1 For Flat Back Screens
TV TVTV
M-A/M-B/M-C M-F
8-2 For Recessed Back Screens or to Access A/V Inputs
TV TVTV
Tighten all screws but do not over tighten.
- Position the adapter brackets as close as possible to the center of the displays.
- Screw the adapter brackets onto the displays.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screens.
M-D/M-E M-F M-H M-G
M-D/M-E M-F M-H
M-C M-D/M-E/ M-F M-G
M-C M-F M-G or or or
9. Hanging the Displays onto the Universal Plates
Note: Leave a one millimeter gap between both displays.
- Lift the display carefully and pull downward two straps at the same time , then hook the adapter brackets to the universal plates. Fasten the adapter brackets to the universal plate by releasing the straps.
- The other displays are hung onto the universal plates in the same way.
Note: The displays are installed to the universal plates from the bottom up.
页 6
1mm 1mm
Use the padlocks to prevent the displays from being stolen (The padlocks are not included).
up down
Note: Leave a one millimeter gap between both displays.
10. Micro-Adjustment
If the displays uptilted, rotate the adjustment screws as shown in figure.
If the displays tilted down, rotate the adjustment screws as shown in figure.
Rotate the adjustment screws as shown in figure to make a one millimeter gap left between the upper and lower displays.
- Adjust the angle of displays by the numerical order given.
- T
- T
- T
Legal & Compliance
Product identification
Model: PDS-2304C – manual version 1.0
Warranty and liability
The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.
The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.
Trademarks and disclaimer
Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.
Packaging
Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.