页 1

PDS-2402 55"

Menu Board Wall Mount

INSTALLATION MANUAL

Caution: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

页 2

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.

• Package M (x2)
• Package W
• ST6.3x55 (x8)
• W-A concrete anchor
• W-B (x8) D6 washer (x8)
• W-C

Note: Read the entire instruction manual before you start installation and assembly.

Caution: Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.

• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
• This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

• wall plate A (x1)
• connecting fitting (x1)
• left adapter bracket C (x2)
• right adapter bracket D (x2)

• M5x14 M-A (x4)
• M6x14 M-B (x4)
• washer M-F (x4)
• M8x20 M-C (x4)
• big spacer M-H (x4)
• M6x30 M-D (x4)
• M8x30 M-E (x4)
• small spacer M-G (x8)

页 3

1b. For Solid Brick and Concrete Mounting

1. Mark the exact location of mounting holes
2. Drill pilot holes (ø 10mm/ø 3/8", 60mm/2.4" depth)

Note: Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

1. Screw the wall plate onto the wall

Caution: Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
Installers are responsible to provide hardware for other types of mounting situations.
Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

1a. For Wood Stud Wall Mounting

Find and mark the exact location of mounting holes (ø 4.5mm/ø 3/16", 55mm/2.2" depth).

Note: If the wall plate fits three wood studs only, please remove the fourth baseplate using a screwdriver. The distance between the baseplates can be adjusted to fit the distance between the wood studs by using a screwdriver.

Tip: Mount the wall plate with the screws facing upward.

页 4

3. Hanging the Displays onto the Wall Plate

2. Installing the Adapter Brackets

Top of the display

2-1 For Flat Back Screens

2-2. For Bump-out or Recessed Back Screens

Tighten all screws but do not over tighten.

• Position the adapter brackets as close as possible to the center of the display.
• Screw the adapter brackets onto the display.

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

页 5

4. Adjustment

-10° to +5°

For Multiple Wall Plates Installation

• Use the padlocks to prevent the displays from being stolen (The padlocks are not included).
• Remove the plastic covers at one end of wall plates using a screwdriver.
• Remove screws at one end of the wall plates using a screwdriver.
• Join the wall plates with the connecting fitting and tighten screws to secure them.
• Lift the display carefully and pull downward two straps at the same time, then hook the adapter brackets to the wall plate.
• Fasten the adapter brackets to the wall plate by releasing the straps.

页 6

Maintenance

• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please contact your distributor if you have any questions.
• Then skip to step1 for installation.

Legal & Compliance

Product identification

Model: PDS-2402 – manual version 1.0

Warranty and liability

The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.

The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.