Assembling the Base
Note: Read the entire instruction manual before you start installation and assembly.
WARNING
- Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
- This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
- This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
- Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items. This greatly reduces their holding power.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
Required for Installation / Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
| left cover A | right cover B | middle base C | connecting plate D | fastener E |
|---|---|---|---|---|
| universal plate F | adapter bracket G | cable cover H | column I | camera shelf J |
| connecting plate K | top cover L | DVD shelf M | left base N | right base O |
| M8x30 (x4) P | M8x40 Q | M6x14 R | M6x12 S | M6x10 T |
| M8x16 U | M4x6 V | M4x6 W | D6 washer X | wrench Y |
| 5mm Allen key Z | ||||
Package M
| M5x14 M-A | M6x14 M-B | M6x30 M-C | M8x30 M-D | M8x50 M-E | washer M-F | small spacer M-G | big spacer M-H |
|---|
Insert the right base into the middle base. Align the holes in the right base to the holes in the middle base. Secure with the connecting plate and the screws. Repeat this step for the left base.
Note: Lock the brakes on the casters to avoid any sudden movements during installation.
Each caster can be adjusted independently for fine tuning adjustments. Slightly turn the nut to lower or raise the base.
Attaching the Columns to the Base
Attach the columns to the base using the screws and washers.
Attaching the Universal Plate to the Column
Pull the pin outwards and pull the inner column upwards at the same time, until the inner column is pulled to the desired height then release the pin to secure.
Tighten the safety screw.
Attach the universal plate to the column using the appropriate screws.
4. Installing the Adapter Brackets
Top of the display
4-1 For Flat Back Screens
4-2. For Bump-out or Recessed Back Screens
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
• Position the adapter brackets as close as possible to the center of the display.
• Screw the adapter brackets onto the display.
Tighten all screws but do not over tighten.
5. Hanging the Display onto the Universal Plate
Hook the display onto the universal plate.
Tighten four screws to secure them.
Note: Make sure the display is mounted correctly and the screws are tightened safely before releasing the display.
6. For Landscape or Portrait View
For portrait view
Remove the two screws to rotate the display 90° clockwise, then retighten the removed two screws into the different hole positions to secure the display.
7. Angle Adjustment
Loosen the knob to adjust the display to the desired angle then tighten the knob to secure.
8. Installing the Camera Shelf
Attach the camera shelf to the connecting plate with the appropriate screws. Tighten all screws using a proper Phillips screwdriver.
9. Installing the DVD Shelf
Remove the screws and nuts.
Attach the fastener to the column using the screws and nuts.
Note: With the mounting holes facing forward.
Attach the DVD shelf to the fastener using the appropriate screws.
10. Installing the Cable Covers
Attach the connecting plate to the universal plate with the appropriate screws and washers. Tighten all screws using an Allen key.
11. Cable Management
Route the cables through the cable covers.
Maintenance
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
- Please contact your distributor if you have any questions.
Legal & Compliance
Product identification
Model: PM-CART-70B – manual version 1.0
Warranty and liability
The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.
The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.
Trademarks and disclaimer
Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.
Packaging
Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.