← Products
LCD Bracket Tilting & Swivel 10-37"
Discontinued

PM-LM-TS32W

LCD Bracket Tilting & Swivel 10-37"

The PureMounts PM-LM-TS32W is a fully movable wall mount for displays that supports swiveling up to 45° left/right and tilting up to 20° up/down, with a fixed wall distance of 90mm. It has a maximum load capacity of …

ManualFAQ
Chapter 1 of 7

Full Motion LED, LCD TV Wall Mount

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.

Caution: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

Caution: The wall structure must be capable of supporting at least five times the weight of the TV and bracket combined. Only install on a vertical wall.

Caution: Read these instructions carefully before using this product. Improper installation may cause property damage or serious personal injury.

  • Do not use this product for any purpose or in any configuration not explicitly specified in these instructions. We hereby disclaim any and all liability for injury or damage arising from incorrect assembly, incorrect use or use on a wall that cannot support the unexpectedly heavy load of the TV and bracket combination.
  • This product should only be installed by someone of good mechanical aptitude, with experience in the use of basic tools.
  • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • Tighten screws firmly, but do not over tighten. Over tightening can damage the items, greatly reducing their holding power.
  • This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
  • Do not use this product for any purpose not explicitly specified by manufacturer.

Note: Ensure that you have received all parts according to the component list (rear side) prior to installation. If any parts are missing or faulty, telephone your local distributor for assistance. Never use substitute parts.

Note: Check that the bracket is secure and safe to use at regular intervals (at least once every three months).

PM-LM-TS32
PM-LM-TS32B
PM-LM-TS32W
50x50/75x75/100x100/200x100/200x200
10-42"
25-107cm
30kg (66lbs) RATED
PureLink GmbH
Von-Liebig-Str. 10 | 48432 Rheine | Germany
Phone: +49 (0) 5971 800 299 0
PureLink GmbH hereby declares that this product complies with Directive 1907/2006/EU and 2011/65/EU.

Chapter 2 of 7

Parts List

PartQuantity
Ax1
Bx1
Cx1
Dx1
Ex1
Fx2
Gx1
Hx1
M4x14 (M-A)x4
M5x14 (M-B)x4
M6x14 (M-C)x4
M8x20 (M-D)x4
M-Ex4
M-Fx4
M-Gx8
W-Ax3
W-Bx3

1a

  • Mounting to wood stud wall:
  • Use a level to mark holes on wall.
  • Drive W-A screws directly into stud (do not use in drywall only).
  • Do not use power drill for final tightening.

1b

  • Mounting to brick/masonry wall:
  • Use a level to mark holes on wall.
  • Drill holes and insert W-B anchors.
  • Use W-A screws to secure.
  • Do not use power drill for final tightening.
Chapter 3 of 7

Step 2

  • Attach B to C using D and E.
Chapter 4 of 7

Step 3

  • Attach bracket (C) to monitor using one of the following screw sets:
  • M-A, M-E, M-F
  • M-B, M-E, M-F
  • M-C, M-E, M-F
  • M-D, M-E, M-F
  • Add spacers (M-G) if required.
  • Use the correct combination for your monitor type.
  • Do not overtighten.
Chapter 5 of 7

Step 4

  • Attach assembly (F, G, H) to the arm.
  • Securely tighten.
Chapter 6 of 7

Step 5

  • With help, mount the display arm assembly to the wall plate.
  • Make sure it is securely attached.
Was this helpful?
← PreviousNext chapter →
Staff sign-in