← Products
PureMounts® TV Bracket - Wire 23-42"
Discontinued

PM-WIRE-37

PureMounts® TV Bracket - Wire 23-42"

PureMounts® TV Mount - Wire 23-42".

Manual
PDF / print
Chapter 1 of 3

Package M

Note: Read the entire instruction manual before you start installation and assembly.

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

  • supporting spacer (x1) D
  • supporting spacer (x1) C
  • (x1) B
  • adapter bracket, wall plate A
  • (x2) ST5.5x50 (x2) W-A
  • concrete anchor W-B
  • (x2) D6 washer W-C
  • (x2) M5x14 M-A
  • (x4) M6x14 M-B
  • (x4) M8x20 M-C
  • (x4) M6x30 M-D
  • (x4) M8x30 M-E
  • (x4) big spacer M-I
  • (x4) small spacer M-H
  • (x8) D5 washer M-F
  • (x4) D8 washer M-G

Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.

  • This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
  • This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual.
  • Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
  • Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
  • Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
Chapter 2 of 3

Package W

1. For Solid Brick and Concrete Mounting

  • Drill pilot holes: 60mm (2.4") apart, ø 8mm (ø 5/16")
  • Mark the exact location of mounting holes

Caution: Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

  • W-B
  • W-C
  • W-A

2. Installing the Adapter Brackets

2-1 For Flat Back Screens

  • Top of the TV
  • M-F, M-G, M-A, M-B, M-C, TV
  • PM-WIRE-37 (60-120mm), PM-WIRE-52 (180-220mm)

2-2 For Bump-out or Recessed Back Screens

Tighten all screws but do not over tighten.

Note: Screw the supporting spacers onto the TV.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

3. Hanging the TV onto the Wall Plate

  • After the wall mount has been safely secured to the wall, carefully lift your TV and hook wirerope into the wall plate rail. Make sure your TV is securely and correctly attached.

Maintenance

  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).
  • Please contact your distributor if you have any questions.

4. Cable Management

  • Fold the tilt supports back once all cables have been installed.
  • Fold out the tilt supports to access the cables.
  • TV, M-H, M-G, M-C, M-G, M-C, M-D, M-E, M-H, M-G, M-D, M-E, M-I, M-G, M-D, M-E, M-I, M-H, or M-H, M-H, M-I, M-H, or M-I, M-G, M-C, M-G, M-C, M-D, M-E, M-G, M-D, M-E, M-G, M-D, M-E
Was this helpful?
← PreviousNext chapter →
Staff sign-in