Safety precautions

• Unpack the equipment carefully and save the original box and packing material for possible future shipment
• Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
• Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Do not put any heavy items on the extension cable in case of extrusion.
• Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards.
• Install the device in a place with fine ventilation to avoid damage caused by overheat.
• Keep the module away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
• Do not twist or pull by force ends of the optical cable. It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Unplug the power cord when left unused for a long period of time.
• Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.

Introduction

PT-PSW-21KVM is an 18Gbps 2x1 switcher extension kit, which supports up to 4K/60/4:4:4, HDR10 and Dolby Vision, HDCP 2.2. It features uncompressed transmission of 18Gbps signals up to 100m. At the same time, it can be connected to peripheral KVM equipment, which is very useful in video conference applications.

Note: HDBaseT 3.0 recommends Category 6a U/FTP as the minimally acceptable cable spec required to achieve its full capabilities and potential.

Feature

• 18G, 4K@60HZ 4:4:4, HDR10, Dolby Vision and HDCP 2.2.
• 1 x HDMI input, 1 x USB-B host, 1 x USB-C input, one HDBaseT output with HDMI loop output,
• 6 USB ports for peripheral devices, 2 USB3.0 on Tx (5Gbps), 4 USB2.0 on Rx (3 USB-A + 1 USB-C), Bandwidth Max up to 250Mbps.
• HDBT 3.0 technology, supports uncompressed 18G signal transmission up to 100m
• USB-C input support 60W charging when system powers up on Tx end.
• The system supports two way PoC.
• Auto switch 5V or TMDS detection
• Support RS232, CEC & TCP/IP control and 3rd party Dry Contact control

Package List

• 1x PT-PSW-21KVM Switcher set
• 5 x 3-pin terminal block
• 6 x screws
• 8 x Plastic Cushions
• 2 x 5-pin terminal block
• 4 x mounting ears
• 1 x DC24V/5A power adapter
• 1 x Manual

Panel Description

Note: Please contact your distributor immediately if any damage or defect in the components is found.

Tranmitter

Front Panel

Note: All the input source LEDs will go out when pressing Black Output button on

Rear Panel

Receiver

Front Panel

Rear Panel

EDID Management

EDID are control by the EDID DIP switch, the specific description is as follows:

• 0000 Learn the display EDID in the default mode: read the EDID of the TX HDMI output and RX HDMI output, and output the EDID with the lower resolution of the two, if you can’t learn it, then use the built-in 1920x1080@60 8bit Stereo
• 0001 1920x1080@60 8bit High Definition Audio
• 0010 3840x2160@60Hz Deep Color Stereo Audio
• 0011 3840x2160@30Hz 8bit Stereo Audio
• 0100 3840x2160@30Hz Deep Color High Definition Audio
• 0101 3840x2160@60Hz 4:2:0 Deep Color Stereo Audio
• 0110 3840x2160@60Hz Deep Color High Definition Audio

• 0111 3840x2160@60Hz Deep Color HDR LPCM 6CH
• 1011 Custom EDID1
• 1100 Custom EDID2
• 1101 Custom EDID3
• 1110 Custom EDID41111 EDID management

Specification

GUI Control

The switcher can be controlled via TCP/IP. The default IP settings are:
IP Address: 192.168.0.178
Subnet Mask: 255.255.255.0
TCP/IP port: 4001

Note: TCP/IP Commands are same as RS232

Type 192.168.0.178 in the internet browser, it will enter the below log-in webpage:
There are three selectable usernames:

The username and password can be changed via Access tab.
Here we login as “admin” as an example to introduce each GUI tab.

Video Tab

Choose the HDMI, USB-C or Auto source according to actual usage.

Configuration Tab

EDID

Choose the desired EDID format or define the appropriate EDID format.

Auto Downscale

Enable or disable the auto Downscale in TX or RX output.

Tags

Choose and enter the tags, then click confirm to change the tags.

CEC Tab

Input

Select the function and press to control the input

Output

Select the function button and press to control the output

User-defined

Define the Trigger of input and output

RS232 Tab

• Baud Rate: Supports 9600, 19200, 38400, 57600, 115200
• Command Ending: NULL, CR, LF or CR+LF can be chosen.
• Command: Type the command in the box to control the third-party device which is connected to the RS232 port of the PT-PSW-21KVM.

Network Tab

• Static IP or Dynamic Host Configuration Protocol (DHCP).
• Modify the static IP Address, Subnet Mask, and Gateway.

Access Tab

• Modify the login username and password.
• Lock or unlock the front panel buttons.
• Enable or disable GUI automatic log-off mode.
• Configure accounts user2 and user3
• Factory default reset

Update Tab

• Factory Default: set the equipment to factory default setting.
• Firmware Update: update FW to the equipment.

RS232 Control Software

• Installation Please download the latest Software Version from the link below: https://docklight.de/download/Docklight.zip Then follow the installation wizard for installation on Windows 7 and 10.
• After the installation, Docklight can be run for the first time and should look like the below screen shot:
• Registration is not necessary unless you wish to save settings on exit, so unless you wish to register click on "OK" to close the window.
• The next pop-up window can also be closed with "Continue". An empty project is enough to send and receive commands easily (The default setting is always “Start with a blank project / blank script“)
• Click “OK” to close this window.

Now you are in the main view, where commands are sent and feedback is received. The next step is to select the correct COM port of the PC. To do this, double-click on "COM1" in the corresponding setup window.
Click “Continue” to close this window.

In the following window, select the drop-down menu labeled "Send / Receive on Comm Channel", select the appropriate COM port and then click on "OK" at the bottom right corner.
All other settings can be left at default for most applications, but refer to device RS232 settings to be sure. Double click on “COM1” to change to the right COM port.

1. In order to be able to send commands, open communication with the device by clicking on "Play".
2. Then the keyboard function must be activated, so that commands can be written in the "communication window".
3. Finally enter the command, for example "50701%". This is then confirmed by pressing "Enter" to send. Any response from the connected device will appear in red. Select the right COM port.

• Enable the keyboard type in function.
• Click “Play” to open the communication.
• Monitoring area, indicates if the command sent works.
• Command sending area

RS232 Command

Communication protocol: RS232 Communication Protocol
Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none
The switcher can be controlled by sending the following RS232 commands:

Note: Please remember to end the commands with the ending symbols “.” or “;”.
Type the command carefully, it is case-sensitive.
All commands ended with “<CR><LF>”.

System control

STA. Status query:
PT-PSW-21KVM V1.0.0
PWON!
HDBT 01 Power ON!
HDMI OUT 01 Down Scale OFF!
HDMI OUT 02 Down Scale OFF!
HDMI Out Switch Auto Mode!
Get Trigger Mode Is 5V.
System Unlock!
Baudrate9600!
GUI_IP:192.168.0.200!
HDMI Out Switch To 02!
Set Output Black Screen ON!
IN 1 2
LINK Y Y
OUT 1 2
LINK Y Y
Input 1 EDID From 1 User Define EDID!
Input 2 EDID From 1 Internal EDID!
OUT 01 HDCP MAT DISPLAY!
OUT 02 HDCP MAT DISPLAY!
Set POFF Delay To 600 Second(s)!

Source control

EDIDUpgrade[xx]. The serial port upgrades EDID data.

1. [xx] represents the input port, the value is 00-02 and U. [xx]=00-02 means to customize the EDID of the corresponding input port (EDID is switched to the custom EDID after customization, and will not be saved in the machine), 00 means to operate on all input ports, 01-02 Means input 01-02,
2. [xx]=U1-U4 means custom built-in EDID (can be saved in the machine and recalled at any time), only one built-in EDID can be customized, and the current EDID still used after the customization is completed will not switch to the customized EDID.

After receiving the instruction, the machine will prompt to send the EDID file. The file format must be .bin within 10s (in order to ensure normal data reception, all HDBaseT must be disconnected before sending the instruction)

Input XX/User Define EDID Upgrade OK By RS232 Or GUI!

EDID/[xx]/[yy]. The input port xx uses the built-in EDID numbered yy.

• [xx] represents the input port, the value 00-02, 00 represents all input ports, 01-02 separately represents input 1-2;
• [yy] represents the built-in EDID number, the value is 01-12, 01-08 represents the built-in EDID that cannot be customized, and 09-12 represents the customized EDID

Input 02 EDID Upgrade OK By 01 Internal EDID!

EDIDM[x]B[y]. The input port learns the EDID of the output port.

• [X] represents the output port number, [X] takes the value 1-2 (or 01-02 Note: 01-02 must be used in conjunction with 00-02 below), 1-2 represents output 1-2.1 represents output 1, 2 represents Output 2.
• [y] represents the input port, the value is 0-2 (00-02), 0 represents all input ports, and 1-2 separates represents input 1-2;

Input 01 EDID Upgrade OK By 02 EXT EDID!

Baudrate[XXX]. Set control baud rate.

• [XXX] Support 115200, 57600, 38400, 19200, 9600

Set Local RS232 Baudrate Is 9600!

CEC[I/O][AA][BB][CC][DD].

• I/O: means input or output port, AA, BB, CC, DD are all hexadecimal data;
• AA: indicates the port number, the input is 01-02, the output is 01-02, and FF means all;
• BB: Indicates the device type (TV: 40, 20, 80, disc player 04, 08, etc.);
• CC: indicates the CEC function category (for example, 44 indicates the remote control function)
• DD: indicates the specific data under the function (for example: 41, representing the volume plus), this can send combined data such as two or three groups, or not, up to 9 groups;

CEC Input 01 Send Success!

CEC Output 01 Send Success!

CEC Output 01 Send Success!

System Diagram

The following diagram illustrates typical input and output connections that can be utilized with the KVM switcher.

PT-PSW-21KVM

Conference room setup with camera, soundbar, transmitter and receiver.

• Camera
• ARC
• Soundbar
• Receiver
• Laptop
• MacBook
• MIC
• Transmitter
• USB:
• HDMI:

• USB-C:
• HDBaseT:
• AUDIO:

Conference room setup with camera, keyboard, mouse, transmitter and receiver.

• Camera
• Receiver
• Laptop
• MacBook
• Keyboard
• Mouse
• Transmitter
• USB:
• HDMI:
• USB-C:

• HDBaseT:

After-Sales Service

If there appear some problems when running the product, please check and deal with the problems referring to this user manual. Any transport costs are borne by the users during the warranty.

1. Product Limited Warranty: This product will be free from defects in materials and workmanship for three years (The purchase invoice shall prevail). Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service.
2. What the warranty does not cover (servicing available for a fee):
3. Technical Support: For any questions or problems, contact your distributor or reseller and tell them the respective product name and version, the detailed failure situation as well as the formation of the cases.

• Warranty expiration.
• Factory applied serial number has been altered or removed from the product.
• Damage, deterioration or malfunction caused by:
• Normal wear and tear.
• Use of supplies or parts not meeting our specifications.
• No certificate or invoice as the proof of warranty.
• The product model showed on the warranty card does not match with the model of the product for repairing or had been altered.
• Damage caused by force majeure.
• Servicing not authorized by distributor.
• Any other causes which does not relate to a product defect.
• Delivery, installation or labor charges for installation or setup of the product.

Asking for Assistance

Technical Support

Phone: +49 5971 800299 - 0
Fax: +49 5971 800299 – 99

Technical Support Hours:
8:30 AM to 5:00 PM Monday thru Thursday
8:30 AM to 4:00 PM Friday

Write to:
PureLink GmbH
Von-Liebig-Straße 10
D - 48432 Rheine
www.purelink.de
info@purelink.de

Legal & Compliance

Product identification

Model: PT-PSW-21KVM – manual version 1.0

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

FCC

Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.

Disposal of electrical and electronic equipment

WEEE reg. no.: DE 93847290

The crossed-out wheelie bin symbol on the product, packaging or in this manual means that electrical and electronic equipment must not be disposed of with household waste at the end of its life. Hand in old devices free of charge at a public collection point or return them to a distributor obliged to take them back. Remove batteries and lamps that can be removed without destroying the device before handing it in, and delete any personal data stored on the device. Details are regulated by national law. By returning old devices you help protect the environment.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.