Safety Precautions

• Unpack the equipment carefully and save the original box and packing material for possible future shipment
• Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
• Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Do not put any heavy items on the extension cable in case of extrusion.
• Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards.
• Install the device in a place with fine ventilation to avoid damage caused by overheat.
• Keep the module away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
• Do not twist or pull by force ends of the optical cable. It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Unplug the power cord when left unused for a long period of time.
• Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.

Product Introduction

Thanks for choosing the HDMI 2.0 6x1 Presentation Switcher. The switcher allows selection of six different sources (three HDMI inputs, one USB-C input, one DisplayPort input and one VGA input), and will simultaneously switch the selected video to HDMI output. It supports video resolution up to 4Kx2K@60Hz 4:4:4 8bit, 1080P, and 3D. In addition, there is the smart built-in EDID setting can be selected by the 4-pin DIP switch on the rear panel.

The switcher supports stereo and multichannel audio on the HDMI inputs. In addition to the audio embedded in the HDMI output stream, the audio is simultaneously de-embedded to an optical digital audio output and a balanced analog audio output.

The switcher features multiple methods of control. When in the AUTO mode, the switcher will automatically switch to the first detected source device. When the active source is removed, the switcher will switch from input 1 to 6. The switcher can be manually controlled by the front panel buttons, IR remote and RS232 command.
CEC allows the display device can be controlled by the front panel buttons and RS232 CEC commands.

Features

• Supports HDMI 2.0 and video resolution up to 4K@60Hz 4:4:4 8bit, 1080P, and 3D.
• 18Gbps high bandwidth and supports HDR 10.
• HDCP 2.2 compliant.
• Supports automatic switching.
• CEC control for display volume and ON/OFF.
• Controllable via RS232 and IR.
• VGA resolution is selectable on the front panel.
• Optical and balanced analog audio for audio de-embedding.
• Smart EDID management for various application and customized setting.

Package List

• 1x PT-PSW-61E HDMI 2.0 6x1 Presentation Switcher
• 2x Mounting Ears with 4 Screws
• 4x Plastic Cushions
• 1x IR Receiver
• 1x IR Remote
• 1x 3-pin Terminal Block
• 1x 5-pin Terminal Block
• 1x Power Adapter (12V DC, 2A)
• 1x User Manual

Note: Please contact your distributor immediately if any damage or defect in the components is found.

Specification

Front Panel

• Power LED: The LED illuminates red when the device is in standby, or illuminates green when the device is power on.
• VIDEO SOURCE: - Press 1~6 button to select input source respectively, and its corresponding LED illuminates green. - Press and hold the AUTO button at least three seconds to enable automatic switching mode, and its LED illuminates green.
• DISPLAY CONTROL: - Press ON to turn on the display. - Press OFF to turn off the display. - Press to mute/unmute display audio. - Press to decrease the audio volume gradually, or press and hold it to decrease the audio volume constantly. - Press to increase the audio volume gradually, or press and hold it to increase the audio volume constantly.
• VGA RESOLUTION: - When the VGA input is selected, press RES repeatedly can set the VGA resolution to 1280x720, 1920x1080 or 1920x1200. - The three LEDs illuminate green to indicate the VGA resolution is selected.
• FW: Micro-USB port for firmware upgrade.

Rear Panel

• VIDEO SOURCE: - Three type-A female HDMI input ports to connect HDMI video source. - One Type-C USB input port to connect the device with SlimPort output, e.g. Macbook. - One DisplayPort input port to connect the DisplayPort video source. - One 15-pin VGA input port to connect the VGA video source, and one stereo auxiliary audio input (3.5mm mini jack) can be embedded in VGA video.
• HDMI OUT: Type-A female HDMI output port to connect the video display.
• OPTICAL: Toslink connector for digital audio output.
• L/R: 5-pin terminal block for balanced audio output.
• EDID: 4-pin DIP switch for EDID setting.
• IR IN: 3.5mm mini jack to connect the IR receiver to control the switcher by the included IR remote.
• RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or a device to be controlled by RS232 commands.
• TCP/IP: RJ45 connector to connect the control device (e.g. PC) to control the switcher via GUI.
• DC 12V: DC barrel port for power adapter connection.

System Connection

Usage Precaution

• Make sure all components and accessories included before installation.
• System should be installed in a clean environment with proper temperature and humidity.
• All of the power switches, plugs, sockets, and power cords should be insulated and safe.
• All devices should be connected before power on.

System Diagram

1. HDMI/MHL IN 2. HDMI/MHL IN 3. HDMI IN 6. VGA IN 4. USB-C IN HDMI OUT OPTICAL
Tx Rx
RS232 IR IN EDID
ON
OFF
1 0
L R
1 2 3 4
5. DP IN TCP/IP
PC
USB-C:
VIDEO:
RS232:
DP:
IR:
GUI Control:
4K TV
Laptop
Blu-Ray
Game Console
MacBook AVR
Remote IR Receiver
Surface Pro 4 PC
HDMI:
VGA:

Manual Switching

When the switcher is in the manual switching mode, the Auto Mode LED goes out. If need to change the input source, please directly press the 1, 2, 3, 4, 5 or 6 button, and the corresponding LED illuminates green immediately.

Automatic Switching

Press and hold the AUTO button at least three seconds to enable automatic switching, and the Auto mode LED will light.

When in the Auto mode, the switcher will switch according to the following rules:

• The switcher will switch to the first available active input starting at input 1 to 6.
• New input: The switcher will automatically select the new input once detecting a new input.
• Reboot: If power is restored to the switcher, it will automatically reconnect the input before powered off.
• Source removed: When an active source is removed, the switcher will switch to the first available active input starting at 1-HDMI/MHL input.
• Press the Video Source button (1, 2, 3, 4, 5 or 6) can directly change the input source. If the corresponding source device is active, it will be switched as input source; otherwise, the switcher will switch to the first available active input starting at 1-HDMI/MHL input.
• Press and hold the AUTO button at least three seconds again can exit AUTO mode, but the input source will remain the current setting.

Display Control

The switcher supports CEC, and the DISPLAY CONTROL buttons on the front panel are designed for Display On/Off and volume adjustment.

• ON: Display On.
• OFF: Display Off.
• : Mute/unmute display audio.
• : Volume down display audio.
• : Volume up display audio.

VGA Resolution Selection

The RES button on the front panel is designed for VGA resolution selection.
OFF: Display Off.
Press RES button repeatedly to set the VGA resolution to 1280x720, 1920x1080 or 1920x1200, and its corresponding LED will illuminates green.

EDID Setting

The Extended Display Identification Data (EDID) is used for the source device to match its video resolution with the connected display. By default, the source device obtains its EDID from the first connected display. Meanwhile, since the displays with different capabilities are connected to the switcher, the 4-pin DIP switch on the rear panel can be used to set the EDID to a built-in fixed value. Use the following table to determine the setting for the 4-pin DIP switch for specific video resolution and audio capabilities.

The switch represents “0” when in the lower (OFF) position, and it represents “1” while putting the switch in the upper (ON) position.

Note: Stereo Audio: LPCM 2ChHigh Definition Audio: LPCM 8Ch, AC-3 6Ch, DTS 5.1, Dolby Digital5.1

IR Remote Control

Connect the IR IN port to an IR receiver, the switcher can be controlled by the below IR remote.

• ① Enter or exit standby mode.

• ② Video input selection buttons (1~6) and AUTO mode button.
• ③ Source device control buttons.

Page Up Page Down

Rewind Fast Forward

Pause/Play Stop

Exit Enter

Left Right

• Power On/Off
• ④ VGA resolution selection buttons.
• ⑤ Display device control buttons.

Power On/Off Mute/Unmute
Volume Down Volume Up
OK
5 6
HDMI 2.0 Presentation Swither
DISPLAY
SOURCE
Manual/Auto
VGA RESOLUTION
1280x720 1360x768 1920x1080 1920x1200
INPUTS
Manual/Auto
# 1
# 2
# 3
# 4
# 5

GUI Control

The switcher also be controlled via TCP/IP, and the default IP setting is:

• IP Address: 192.168.0.178
• Subnet Mask: 255.255.250.0

Please type 192.168.0.178 in the internet browser, and it will enter the below log-in webpage:
Username: admin
Password: admin
Please type the user name and password, and then click Login to enter the section for video switching.

Switching Tab

• Click the AUTO button to enable automatic switching mode.
• Click 1~6 button to select input source respectively.

Display Control Tab

1. CEC Control
2. ON: Display On.
3. OFF: Display Off.
4. : Mute/unmute display audio.
5. : Volume down display audio.
6. : Volume up display audio.

VGA Resolution Selection

• VGA output resolution can be selected as 1024x768@60Hz, 1280x720@50Hz, 1280x720@60Hz, 1360x768@60Hz, 1600x1200@60Hz, 1920x1080@50Hz, 1920x1080@60Hz (Default) or 1920x1200@60Hz.

Audio Tab

• Turn on or turn off the digital audio output.
• Turn on or turn off the analog audio output.

EDID Tab

• Before select EDID in this tab, please ensure the 4-pin DIP switch on the rear panel is on the “1111” position.
• User-defined EDID: There are four EDID values can be customized by the below steps:

1. Prepare the EDID file (.bin) on the control PC.
2. Select the user-defined 1/2/3/4.
3. Click the black box , and then select the EDID file (.bin) according the tooltip.
4. Click Apply to upload the user-defined EDID.

RS232 Tab

• Baud Rate: Supports 2400, 4800, 9600, 19200, 38400, 57600 or 115200.
• Command Ending: NULL, CR, LF or CR+LF can be chosen.
• Command: Type the command in this box to control the third-party device which is connected to the RS232 port of the switcher.

Interface Tab

• Modify the title bar label.
• Modify the button labels.

Access Tab

• Modify the login password.
• Lock or unlock the front panel buttons.

Network Tab

• Set Static IP or Dynamic Host Configuration Protocol (DHCP).
• Modify the static IP Address, Subnet Mask, and Gateway.

GUI Upgrade

Please visit at http://192.168.0.178:100 for GUI online upgrade.
Type the username and password (the same as the GUI log-in setting, modified password will be available only after rebooting) to login the configuration interface.
After that, click Administration in the source menu to get to Upload Firmware as shown below:

Select the update file and click Apply button, and then it will start upgrade process.

RS232 Control Software

Installation: Copy the control software file to the control PC.
Uninstallation: Delete all the control software files in corresponding file path.

Basic Setting: Connect the switcher with all input devices and output devices needed, then to connect it with a PC which is installed with RS232 control software. Double-click the software icon to run this software.
Here take the software CommWatch.exe as an example:

Please set the parameters of COM number, bound rate, data bit, stop bit and the parity bit correctly, and then the command is ready to be sent in command sending area.
Parameter configuration area
Monitoring area, show the commands and its feedback information.
Command sending area
Operation area

RS232 Command

Communication protocol: RS232 Communication Protocol
Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none

Note: All commands not need to end with “<CR><LF>”.
In the commands, “[” and “]” are symbols for easy reading and do not need to be typed in actual operation.
Please remember to end the commands with the ending symbols “.” or “;”.
Please type the command carefully due to case-sensitive.

Device Control

Source Switching

VGA Resolution Selection

When VGA source is selected, the below commands can be used to set the VGA output resolution.

EDID Management

User-define EDID
There are four EDID values can be customized by sending the below command.
Note: When send the below commands to configure EDID, the 4-pin EDID DIP switch on the rear panel must be in the “1111” status.

Audio Control

Display Control

CEC Control

If the input sources and display support CEC, they can be controlled by sending the below command to replace IR remote.

Third-party Device Control

The switcher supports RS232 pass-through control, the third-party device can be controlled by RS232 command, and the command format as shown below:

Panel Drawing

FW
VIDEO SOURCE DISPLAY CONTROL
ON OFF1 2 3 4 5 6 AUTO RES1920x1080 1280x720 1920x1200

VGA RESOLUTION

• 1. HDMI/MHL IN
• 2. HDMI/MHL IN
• 3. HDMI IN
• 4. USB-C IN
• 5. DP IN
• 6. VGA IN

• HDMI OUT
• OPTICAL
• Tx
• Rx
• RS232
• IR IN
• EDID

• ON
• OFF
• 1
• 0
• L R
• 1 2 3 4

• TCP/IP

342.5mm
26.0mm
115.0mm
6x1
Presentation Switcher
Multiformat 4K (60Hz 4:4:4), HDMI Out
PT-PSW-61E

Troubleshooting & Maintenance

Note: If the problem still remaining after following the above troubleshooting steps, please contact your local dealer or distributor for further assistance.

After-Sales Service

If there appear some problems when running the product, please check and deal with the problems referring to this user manual. Any transport costs are borne by the users during the warranty.

1. Product Limited Warranty: The product will be free from defects in materials and workmanship for two years (The purchase invoice shall prevail). Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service.
2. What the warranty does not cover (servicing available for a fee):
3. Technical Support: For any questions or problems, contact your distributor or reseller and tell them the respective product name and version, the detailed failure situation as well as the formation of the cases.

• Warranty expiration.
• Factory applied serial number has been altered or removed from the product.
• Damage, deterioration or malfunction caused by:
• Normal wear and tear.
• Use of supplies or parts not meeting our specifications.
• No certificate or invoice as the proof of warranty.
• The product model showed on the warranty card does not match with the model of the product for repairing or had been altered.
• Damage caused by force majeure.
• Servicing not authorized by distributor.
• Any other causes which does not relate to a product defect.
• Delivery, installation or labor charges for installation or setup of the product.

Asking for Assistance

Technical Support:
Phone: +49 5971 800299 - 0
Fax: +49 5971 800299 – 99
Technical Support Hours:
8:30 AM to 5:00 PM Monday thru Thursday
8:30 AM to 4:00 PM Friday

Write to:
PureLink GmbH
Von-Liebig-Straße 10
D - 48432 Rheine
www.purelink.de
info@purelink.de

Legal & Compliance

Product identification

Model: PT-PSW-61E – manual version 1.0

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

FCC

Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.

Disposal of electrical and electronic equipment

WEEE reg. no.: DE 93847290

The crossed-out wheelie bin symbol on the product, packaging or in this manual means that electrical and electronic equipment must not be disposed of with household waste at the end of its life. Hand in old devices free of charge at a public collection point or return them to a distributor obliged to take them back. Remove batteries and lamps that can be removed without destroying the device before handing it in, and delete any personal data stored on the device. Details are regulated by national law. By returning old devices you help protect the environment.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.