Safety precautions

To ensure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference.

• Unpack the equipment carefully and save the original box and packing material for possible future shipment.
• Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
• Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Do not put any heavy items on the extension cable in case of protrusion.
• Do not remove the housing of the device as opening or removing the housing may expose you to dangerous voltage or other hazards.
• Install the device in a place with sufficient ventilation to avoid damage caused by overheat.
• Keep the module away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
• Do not twist or pull by force ends of the optical cable. It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Unplug the power cord when left unused for a long period of time.
• Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.

Product Introduction

Thanks for choosing the PT-SW-HD3A HDMI 2.0 3x1 Switcher with three HDMI video inputs and one HDMI output including automatic signal switching. It supports HDMI video resolutions up to 4K@60Hz, 4:4:4 with HDR, Dolby Vision and multichannel audio support.
In auto-switching mode, it switches to an HDMI input as soon as a new source is connected. When the active input is removed, the switcher will select the first source with the lowest numbered input. The switcher can be controlled via IR using the remote or with the source push-button on the front panel.

Features

• Switches three HDMI inputs to one HDMI output.
• Supports video resolution up to 4Kx2K@60Hz 4:4:4 and 1080P.
• Supports HDR 10 and Dolby Vision formats.
• 18Gbps high bandwidth.
• Fully compliant with HDMI 2.0 and HDCP 2.2 specifications.
• Controllable with IR remote control.
• Powered via the HDMI input source, no need of any external power supply, simplifying installation and operation.
• Supports CEC pass-through.
• Provides four LEDs to indicate the current operating status.
• Cost efficient.
• Metal design.

Package List

• 1x HDMI 2.0 3x1 Switcher
• 1x IR Remote
• 1x User Manual

Note: Please contact your distributor immediately if any damage or defect in the components is found.

Technical Specification

Note: Please only use high-quality HDMI cables, fully compliant with HDMI 2.0 for a reliable transmission and connection.

Front Panel

• ① IR: Built-in IR sensor to receive IR signals from the IR remote to control the switcher.
• ② INPUT 1~3 LED: The LED illuminates blue when the corresponding input channel is selected and there is an HDMI signal input detected. The LED blinks blue when the corresponding input channel is selected but no signal input is detected.
• ③ AUTO LED: The LED illuminates blue in automatic switching mode. The LED is off in manual switching mode.
• ④ SOURCE AUTO/3S Button: Press to switch to next input source. Press and hold at least three seconds to switch between manual switching mode and automatic switching mode.

Rear Panel

• ① HDMI IN 1~3: Three type-A female HDMI input ports to connect HDMI sources.
• ② HDMI OUT: Type-A female HDMI output port to connect HDMI display.

System Connection

Usage Precaution

• Make sure all components and accessories are included before starting the installation.
• System should be installed in a clean environment with proper temperature and humidity.
• All of the power switches, plugs, sockets, and power cords should be insulated and safe.
• All devices should be connected before being powered on.

System Diagram

The following diagram illustrates typical input and output connections that can be utilized with this switcher:
4K TV
Game Console
Laptop
Blu-Ray
IR Control
Remote

Button Control

Manual Switching

When the switcher is in manual switching mode, the AUTO LED is off. Please press the SOURCE AUTO/3S button to switch to the next input.

Automatic Switching

Press and hold the SOURCE AUTO/3S button at least three seconds to enable automatic switching mode. The AUTO LED will turn to blue.

When in the AUTO mode, the switcher will switch according to the following rules:

• Press and hold the SOURCE AUTO/3S button at least three seconds again to exit AUTO mode. The active input source will not be changed.
• By pressing the SOURCE AUTO/3S button, the input source can intentionally be changed.
• New Input: Upon detecting a new input, the switcher will automatically select the new input.
• Reboot: Once power is restored to the switcher, the switcher will output the last active input signal, if available. Otherwise, the switcher will switch to the first available active input starting at HDMI IN 1.
• Source Removed: When an active source is removed, the switcher will switch to the first available active input starting at HDMI IN 1.

IR Remote Control

• AUTO: Enable or disable automatic switching mode.
• INPUTS: Press 1~3 to select the corresponding HDMI input source.

Panel Drawing

• 105.0 mm
• 18.0 mm
• 55.0 mm

Troubleshooting & Maintenance

Note: If your problem is still remaining after following the troubleshooting steps above, please contact your local dealer or distributor for further assistance.

After-Sales Service

If problems appear when using the product, please deal with the problems referring to this user manual. During the warranty period, any transport costs are borne by the customer.

1. Product Limited Warranty: The product will be free from defects in materials and workmanship for two years (The purchase invoice shall prevail). Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service.
2. What the warranty does not cover (servicing available for a fee):
3. Warranty expiration.,Factory applied serial number has been altered or removed from the product.,Damage, deterioration or malfunction caused by:,Normal wear and tear.,Use of supplies or parts not meeting our specifications.,No certificate or invoice as the proof of warranty.,The product model shown on the warranty card does not match with the model of the product for repairing or had been altered.,Damage caused by force majeure.,Servicing not authorized by distributor.,Any other causes which does not relate to a product defect.,Delivery, installation or labor charges for installation or setup of the product.
4. Technical Support: For any questions or problems, contact your distributor or reseller and tell them the respective product name and version, the detailed failure situation as well as the formation of the cases.

Asking for Assistance

Technical Support:
Phone: +49 5971 800299 - 0
Fax: +49 5971 800299 - 99
Technical Support Hours:
8:30 AM to 5:00 PM Monday thru Thursday
8:30 AM to 4:00 PM Friday
Write to:
PureLink GmbH
Von-Liebig-Straße 10
D - 48432 Rheine
www.purelink.de
info@purelink.de

Legal & Compliance

Product identification

Model: PT-SW-HD3A – manual version 1.0

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

FCC

Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.

Disposal of electrical and electronic equipment

WEEE reg. no.: DE 93847290

The crossed-out wheelie bin symbol on the product, packaging or in this manual means that electrical and electronic equipment must not be disposed of with household waste at the end of its life. Hand in old devices free of charge at a public collection point or return them to a distributor obliged to take them back. Remove batteries and lamps that can be removed without destroying the device before handing it in, and delete any personal data stored on the device. Details are regulated by national law. By returning old devices you help protect the environment.

Batteries

Batteries must not be disposed of with household waste. Return used batteries free of charge to collection points or retailers.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.