Introduction

Thank you for choosing the active USB 3.1 Gen 2 AOC cable. This cable allows you to transmit USB signals without external Power Delivery up to a distance of 15 m. The cable is a hybrid cable containing both optical glass fibers and copper conductors. It supports a maximum data rate of 10 Gbit/s per channel, is lightweight, flexible, and has a very small bending radius of only 20 mm.

Intended Use

Use is only permitted indoors, not outdoors. Contact with moisture, e.g. in bathrooms or similar places, must be strictly avoided.
For safety and approval reasons (CE), you must not modify or alter the product. Using the product for purposes other than those described above may damage the product. Improper use can also cause hazards such as short circuits, fire, electric shock, etc.
Please read the user manual carefully and keep it. Only pass the product on to third parties together with the user manual.

Safety Instructions

Please read the user manual carefully and especially pay attention to the safety instructions. If you do not follow the safety instructions and the information on proper handling in this user manual, we assume no liability for resulting personal or property damage. In such cases, the warranty/guarantee will also expire.

This product is not a toy. Keep it away from children and pets. Do not leave the packaging material lying around carelessly. It could become a dangerous toy for children. Risk of suffocation!

The maximum tensile load of the cable is 157N (16kg). Never pull the cable with a higher load. The minimum bending radius of the hybrid cable is approximately 20 mm. Bending the cable to a smaller radius will cause irreversible damage.

Beware of trip hazards; ensure the cable is securely installed.

Protect the product from extreme temperatures, direct sunlight, strong shocks, high humidity, moisture, flammable gases, vapors, and solvents.

Do not expose the product to mechanical stress.

If safe operation is no longer possible, take the product out of service and protect it from unintended use.

• shows visible damage
• no longer functions properly
• has been stored for an extended period under unfavorable environmental conditions, or
• has been subjected to significant transport stress.

Handle the product carefully. Shocks, impacts, or even drops from low heights can damage the product.

Also observe the safety instructions and operating manuals of other devices to which the product is connected.

Consult a specialist if you have doubts about the operation, safety, or connection of the product.

Scope of Delivery

• 1x USB 3.1 AOC cable
• 1x User manual DE/EN
• 1x Warning notice

Features

• complies with USB 3.1 Gen2 standard, achieves bandwidth up to 10 Gbps
• delivers up to 1.5 W over distances up to 15 m
• no external Power Delivery required
• optical hybrid cable with glass fiber and copper wire
• backward compatible with USB 3.0 / 2.0 / 1.1
• no RF interference, operates stably in complex environments

Application

This cable can be used for, among other things:

• Computers / PCs
• TVs / Displays
• Mobile Phones
• Power Banks
• Cameras
• … and more can be used

Specifications

Mechanical Properties & Environmental Compatibility

Specifications

Environmental Conditions

• Operating Temperature: -10 – 50 °C
• Storage Temperature: -20 – 60 °C
• Relative Humidity: 10 – 80 %RH

Cross Section

Construction

Hybrid cable, fiber optic (High Speed Data), copper (Low Speed Signals)

Cable Construction

• 2 fiber cores and 2 copper conductors
• Cable jacket: PVC
• Diameter: 4.5mm
• Connector dimensions: AM: 40 x 18 x 9mm, Type-C: 41 x 15 x 7.5mm
• Connection material: zinc alloy

Jacket
Fiber
AL/MY Foil
Cotton Filler Material
Conductor
Insulation

Operating and Connection Diagram

Note: The FX-I630 series is designed for use with a +5V passive Power Delivery supplied by the source device. Both this +5V connection and the power supply for the integrated fiber optic module are transmitted to the Receiver via a pure standard copper connection. Please ensure the source device can supply more than 500 mA.

This cable can only be used in one direction. The connectors are labeled “HOST” and “DEVICE”. Each plug must be connected to the correct device to avoid signal loss.

Before using this cable, ensure that all devices connected with the AOC-USB cable are switched off and not powered.

1. Connect the “HOST” side of the USB plug to the Transmitter and the “DEVICE” side of the other USB plug to the Receiver / Display. This works without additional Power Delivery.
2. We advise against using additional cables or adapters between connectors, as this may degrade signal transmission performance.
3. Turn on the Transmitter/source device and the Receiver/display.

Maintenance

There are no components inside the product that require maintenance from you; therefore, never open or disassemble it.
Have maintenance, adjustments, and repairs carried out exclusively by a professional or an authorized service center.
If you have any questions not answered in this manual, please contact our technical customer service or a qualified expert.

Cleaning

Before cleaning, disconnect the product from all connected devices.
Do not use scouring agents, solvents, aggressive cleaning agents, cleaning alcohol, or other chemical solutions as they can damage the housing or impair functionality.
For cleaning, a dry, soft, and clean cloth is sufficient. Do not press too hard on the housing to avoid scratch marks. Dust can be easily removed with a long-haired, soft, and clean brush.

Warranty and Liability

The manufacturer grants the statutory warranty of 2 years on a new product.
Since the manufacturer has no influence on the installation of the product, the warranty and guarantee cover only the product itself.
If a fault or defect is found in your product, please contact your specialist dealer and, if applicable, present your receipt or invoice as proof of purchase. Your dealer will either repair the fault on-site or forward the product to the manufacturer. You make our technicians’ work much easier if you describe any faults in detail – only then can you be assured that even rarely occurring faults will be detected and resolved!

The manufacturer is not liable for personal injury or property damage caused by improper installation, operation, or maintenance that is not described in this manual.
Do not alter or modify the product or its accessories.
Any use other than described in this operating manual is prohibited and will void warranty, guarantee, and liability.

CE Compliance

PureLink GmbH hereby declares that FX-I630 complies with Directive 2014/30/EU.
The full text of the EU Declaration of Conformity is available at the following internet address:
www.purelink.de/ce/FX-I630-XXX_CE.pdf

Disposal of Device

WEEE Reg. No.: DE 93847290
Electrical and electronic equipment must not be disposed of with household waste according to the European WEEE Directive. As a consumer, you are obliged under the ElektroG to return electrical and electronic equipment at the end of its life to designated public collection points or to the point of sale free of charge. Details are regulated by the respective national legislation. The symbol on the product, user manual, or packaging indicates these regulations. By disposing of old devices in this manner, you make an important contribution to environmental protection.

Disclaimer

The product complies with legal, national, and European requirements. All company names and product designations contained are trademarks of their respective owners.
All rights reserved.
Typographical errors and changes to the device, packaging, or manual are reserved.
PureLink GmbH

Von-Liebig-Straße 10
48432 Rheine
Germany
Tel.: +49 (0) 5971 800 299-0
Fax: +49 (0) 5971 800 299-99
info@purelink.de
www.purelink.de

Legal & Compliance

Product identification

Model: FX-I630-010 – manual version 1.0

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.