Introduction

Thank you for choosing the active USB3 3.1 AOC cable. This cable allows you to transmit USB signals without external Power Delivery over distances up to 15m. The cable is a hybrid cable that contains both optical glass fibers and copper conductors. It supports a maximum data rate of 10 Gbit/s per channel, is lightweight, flexible, and has a very small bending radius of only 20 mm.

Intended Use

Use is only permitted indoors and not outdoors. Contact with moisture, e.g. in bathrooms or similar environments, must be strictly avoided.
For safety and approval reasons (CE), do not modify and/or alter the product. Using the product for purposes other than those described may damage the product and cause hazards such as short circuits, fire, electric shock, etc.
Read the user manual carefully and keep it. Only pass the product on to third parties together with the user manual.

Safety Instructions

Read the user manual carefully and pay particular attention to the safety instructions. If the safety instructions and proper handling described in this manual are not followed, we assume no liability for resulting personal injury or property damage. In such cases, the warranty/guarantee also expires.

This product is not a toy. Keep it away from children and pets. Do not leave packaging materials lying around carelessly. These could become a dangerous toy for children. Risk of suffocation!

• The maximum tensile load of the cable is 157N (16kg). Never pull the cable with a higher load.
• The minimum bending radius of the hybrid cable is approx. 20 mm. Bending the cable to a smaller radius will cause irreversible damage.
• Beware of tripping hazards; make sure the cable is securely installed.
• Protect the product from extreme temperatures, direct sunlight, strong vibrations, high humidity, moisture, flammable gases, vapors, and solvents.
• Do not expose the product to mechanical stress.
• If safe operation is no longer possible, take the product out of service and protect it from unintended use.

Safe operation is no longer guaranteed if the product:

• shows visible damage
• no longer functions properly
• has been stored for an extended period under unfavorable environmental conditions, or
• has been subjected to significant transport stresses.

Handle the product carefully. Impacts, shocks, or even a drop from a low height can damage the product.
Also observe the safety notes and operating instructions of other devices to which the product is connected.
Consult an expert if you have doubts regarding the operation, safety, or connection of the product.

Scope of Delivery

• 1x USB3 3.1 AOC cable
• 1x User manual DE/EN
• 1x Safety notice

Features

• complies with USB 3.1 Gen2 standard, achieves bandwidth up to 10 Gbps
• delivers up to 1.5 W over distances up to 15 m
• external Power Delivery not required
• optical hybrid cable with glass fiber and copper wire
• backward compatible with USB3 3.0 / 2.0 / 1.1
• no RF interference, operates stably in complex environments

Application

This cable can be used, among others, for:

• Computers / PCs
• Wearables
• TVs / Displays
• Projectors
• Mobile Phones
• Power Banks
• Cameras
• Home Theaters
• Medical Applications
• LED Video Walls
• TV Stations
• Conference Rooms
• Digital Signage
• … and more

Specifications

Mechanical Properties & Environmental Compatibility

Specifications

Environmental Conditions

Cross Section

Structure

Hybrid cable, fiber optic (High Speed data), copper (Low Speed signals)

Cable Construction

• 2 fiber cores and 2 copper conductors
• Cable jacket: PVC
• Diameter: 4.5mm
• Connector dimensions: Type-A plug: 40 x 18 x 9 mm
• Type-A socket: 49 x 18 x 9 mm
• Connection material: Zinc alloy

• Jacket
• Optical Fiber
• AL/MY Foil
• Cotton Filling Material
• Inner Conductor
• Insulation

Operating and Connection Diagram

Note: The FX-I650 series is designed for use with a +5V passive Power Delivery supplied by the source device. This +5V connection, as well as the power for the integrated optical fiber module, is transmitted to the Receiver via a standard copper connection. Please ensure that the source device can supply more than 500 mA.

This cable can only be used in one direction. The connectors are labeled “HOST” and “DEVICE.” Each plug must be connected to the correct device to avoid signal loss.

Make sure before using this cable that all devices connected with the AOC USB cable are turned off and not powered.

1. Connect the “HOST” side of the USB plug to the Transmitter and the “DEVICE” side of the other USB plug to the Receiver / Display. This works without additional Power Delivery.
2. We advise against using additional cables or adapters between the connectors, as signal transmission performance may be weakened.
3. Power on the Transmitter/source device and the Receiver/display.

Maintenance

There are no user-serviceable parts inside the product; therefore, never open/disassemble it.
Have maintenance, adjustments, and repairs performed only by qualified personnel or a specialist workshop.
If you have any questions not answered in this manual, please contact our technical support or a qualified expert.

Cleaning

Before cleaning, disconnect the product from all connected devices.
Do not use abrasives, solvents, aggressive cleaners, cleaning alcohol, or other chemical solutions, as these may damage the housing or impair functionality.
Cleaning requires only a dry, soft, and clean cloth. Do not press hard on the housing to avoid scratches. Dust can be easily removed with a long-haired, soft, and clean brush.

Warranty and Liability

The manufacturer grants the statutory warranty of 2 years on a new product.
Since the manufacturer has no influence on the product installation, warranty and guarantee cover only the product itself.
If a fault or defect is found on your product, please contact your dealer and present your receipt or invoice as proof of purchase. Your dealer will either fix the fault on site or forward the product to the manufacturer. Providing a detailed description of any faults greatly assists our technicians – only then can even rarely occurring faults be reliably identified and corrected!
The manufacturer is not liable for personal injury or property damage caused by improper installation, operation, or maintenance not described in this manual.
Do not alter or modify the product or its accessories.
Any use other than that described in this manual is not permitted and leads to loss of warranty, guarantee, and liability exclusion.

CE Compliance

PureLink GmbH hereby declares that the FX-I650 complies with Directive 2014/30/EU.
The full text of the EU Declaration of Conformity is available at:
www.purelink.de/ce/FX-I650-XXX_CE.pdf

Device Disposal

WEEE Reg. No.: DE 93847290
Electrical and electronic devices must not be disposed of with household waste according to the European WEEE directive. As a consumer, you are obliged under the ElektroG to return electrical and electronic devices free of charge at designated public collection points or the point of sale at the end of their life cycle. Details are regulated by local laws. The symbol on the product, user manual, or packaging indicates these regulations. This type of recycling of end-of-life devices makes an important contribution to protecting our environment.

Disclaimer

The product complies with legal, national, and European requirements. All company names and product designations contained are trademarks of their respective owners.
All rights reserved.
Printing errors and changes to the device, packaging, or manual are reserved.

Legal & Compliance

Product identification

Model: FX-I650-005 – manual version 1.0

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.