Discontinued
PT-FMX-32
PureTools - Flexible Matrix 32-port chassis, 4K seamless, I/O auto detect
PureTools - Flexible Matrix 32-port chassis, 4K, I/O auto detect, GUI.
Control (TCP/IP)FAQCEAvailable control interfaces. Expand an active type to see the full command table.
No matching commands.
RS232 Control106 commandsActive
Source: manual, chapter RS232 Control, page 25
| Command | Description | Response | |
|---|---|---|---|
| /*Type; | Inquire the model | XXXXX | |
| /%Lock; | Lock the front panel buttons | System Locked! | |
| /%Unlock; | Unlock the front panel buttons | System Unlock! | |
| /^Version; | Inquire the firmware version | VX.X.X | |
| /:MessageOff; | Turn off the feedback from the com port. It only shows “switcher OK”. | /:MessageOff; | |
| /:MessageOn; | Turn on the feedback from the com port. | /:MessageOn; | |
| Undo. | Cancel the previous operation. | Undo Ok! | |
| Demo. | Switch to the “demo” mode, 02->01, 2->2, 3->3 … and so on. | Demo Mode AV: 02-> 01 …… | |
| [x]All. | Transfer signal from Input [x] to all outputs | 02 To All. | |
| All@. | Switch on all the outputs | All Open. | |
| All$. | Switch off all the outputs | All Closed. | |
| [x]@. | Switch on output [x] | 02 Open. | |
| [x]$. | Switch off output [x] | 01 Closed. | |
| [x1]V[x2],[x3],[x4]… | Transfer signal from input [x1] to output [x2],[x3],[x4].., separate output channels with “,” | AV: 01->07 AV: 01->08 … | |
| Save[Y]. | Save the present operation to the preset command [Y], [Y]=0~9 | Save To F1 | |
| Recall[Y]. | Recall the preset command [Y] | Recall From F1 AV: 02->04 AV: 02->06 … | |
| Clear[Y]. | Clear the preset command [Y] | Clear F1 | |
| EDIDMInit. | Reset factory default EDID | EDIDMInit. | |
| EDIDM[X]B[Y]. | Manage EDID, enable input [Y] learn EDID data from output [X] | EDIDM07B03 | |
| PWON. | Work normally | PWON | |
| PWOFF. | Enter standby mode | PWOFF | |
| STANDBY. | Enter standby mode, can be awaken via front panel button operations | STANDBY | |
| /+[Y]/[X]:******. | Set communication between PC and HDBaseT receiver. ① Y is for RS232 port (connect with RS232 port of HDBaseT receiver) a. Y = 1 ~ 16, send this command to the corresponding HDBaseT receiver to control far-end device when the Matrix Switcher is working properly. b. Y = A ~ P, send this command to the corresponding HDBaseT receiver when the Matrix Switcher is PWON. c. Y = a ~ p, send this command to the corresponding HDBaseT receiver when the Matrix Switcher is PWOFF. ② X is for baud rate, its value ranges from 1 to 7 (1=2400；2=4800；3=9600；4=19200；5=38400；6=57600；7=115200 ③ ***** is for data (max 48 Byte). | 601% Volume of MIC : 60 (****** and feedback from HDBT receiver) | |
| CustomerSerial:11 | customer serial is 1111111111111111111 | ||
| HDCPON. | Open HDCP for all output cards. | HDCP ON | |
| HDCPOFF. | Close HDCP for all output cards. | HDCP OFF | |
| %0911. | Reset factory default | Factory Default | |
| Status[x]. | Inquire the respective input for output [x] | AV:01-> 02 | |
| Status. | Inquire respective inputs for all outputs | AV:01->02 AV:03->06 … … | |
| CheckInKatype. | Get the input signal card type *-- no available input signal card/output card, 1--VGA, 2--DVI, 4--BT, 5--SDI, 6--HDMI | Channel IN:*11*4**11*4*. | |
| CheckOutKatype. | Get the output signal card type *-- no available output signal card/input card, 1--VGA, 2--DVI, 4--BT, 6--HDMI | Channel OUT: ***4*62**1**. | |
| %9961. | Get current keylock status | System Unlock!/ System Locked! | |
| %9962. | Inquire current working status | PWON/STANDBY/PWOFF | |
| %9963. | Return all input& output connection status | Port 01 02 03 04 Mode In In In In Port 05 06 07 08 Mode In Ou In In Port 09 10 11 12 Mode Ou Ou In Ou Port 13 14 15 16 Mode Ou Ou Ou Ou | |
| %9964. | Inquire the IP | IP: 192.168.0.178 | |
| %9973. | Return resolutions of all outputs | Resolution Out02 1920x1080P 60 Resolution Out04 1920x1080P 60 … … | |
| %9974. | Get current HDCP Status of output port. “X” means input port or no signal cards. “Y” means the output signal traffic with HDCP; “N” means not. | Out 01 02 03 04 HDCP X X X X Out 05 06 07 08 HDCP X N X X Out 09 10 11 12 HDCP N N X N Out 13 14 15 16 HDCP N N N N | |
| %9975. | Get current input & output card correspondence status | Out | 01 | 02 | 03 | 04 In | 00 | 00 | 00 | 00 Out | 05 | 06 | 07 | 08 In | 00 | 01 | 00 | 00 Out | 09 | 10 | 11 | 12 In | 01 | 01 | 00 | 01 Out | 13 | 14 | 15 | 16 In | 01 | 01 | 01 | 01 | |
| %9976. | Get the output card type | Channel 6 output mode is Digital Channel 9 output mode is Digital … … | |
| %9978. | Inquire output resolution configuration mode (manual/auto EDID) | Channel xx is auto/manual signal format. | |
| %9979. | Inquire the customer serial number | customer serial is 1111111111111111111 | |
| %9981. | Inquire input/output type of current inserted cards | If there is no card inserted in a slot, it will show “Nc” instead of In/Ou. Port | 01 | 02 | 03 | 04 Mode | In | In | In | In Port | 05 | 06 | 07 | 08 Mode | In | Ou | In | In Port | 09 | 10 | 11 | 12 Mode | Ou | Ou | In | Ou Port | 13 | 14 | 15 | 16 Mode | Ou | Ou | Ou | Ou Channel status has changed. | |
| %8800. | Get the command sent to ports when PWON | Port 1: 1A1. when PWON | |
| %8801. | Get the command sent to ports when PWON | Port 2: 1A1. when PWON | |
| %8802. | Get the command sent to ports when PWON | Port 3: 1A1. when PWON | |
| %8803. | Get the command sent to ports when PWON | Port 4: 1A1. when PWON | |
| %8804. | Get the command sent to ports when PWON | Port 5: 1A1. when PWON | |
| %8805. | Get the command sent to ports when PWON | Port 6: 1A1. when PWON | |
| %8806. | Get the command sent to ports when PWON | Port 7: 1A1. when PWON | |
| %8807. | Get the command sent to ports when PWON | Port 8: 1A1. when PWON | |
| %8808. | Get the command sent to ports when PWON | Port 9: 1A1. when PWON | |
| %8809. | Get the command sent to ports when PWON | Port 10: 1A1. when PWON | |
| %8810. | Get the command sent to ports when PWON | Port 11: 1A1. when PWON | |
| %8811. | Get the command sent to ports when PWON | Port 12: 1A1. when PWON | |
| %8812. | Get the command sent to ports when PWON | Port 13: NO Data when PWON | |
| %8813. | Get the command sent to ports when PWON | Port 14: NO Data when PWON | |
| %8814. | Get the command sent to ports when PWON | Port 15: NO Data when PWON | |
| %8815. | Get the command sent to ports when PWON | Port 16: NO Data when PWON | |
| %8816. | Get the command sent to ports when PWOFF | Port 1: 2A1. when PWOFF | |
| %8817. | Get the command sent to ports when PWOFF | Port 2: 2A1. when PWOFF | |
| %8818. | Get the command sent to ports when PWOFF | Port 3: 2A1. when PWOFF | |
| %8819. | Get the command sent to ports when PWOFF | Port 4: 2A1. when PWOFF | |
| %8820. | Get the command sent to ports when PWOFF | Port 5: 2A1. when PWOFF | |
| %8821. | Get the command sent to ports when PWOFF | Port 6: 2A1. when PWOFF | |
| %8822. | Get the command sent to ports when PWOFF | Port 7: 2A1. when PWOFF | |
| %8823. | Get the command sent to ports when PWOFF | Port 8: 2A1. when PWOFF | |
| %8824. | Get the command sent to ports when PWOFF | Port 9: 2A1. when PWOFF | |
| %8825. | Get the command sent to ports when PWOFF | Port 10: 2A1. when PWOFF | |
| %8826. | Get the command sent to ports when PWOFF | Port 11: 2A1. when PWOFF | |
| %8827. | Get the command sent to ports when PWOFF | Port 12: 2A1. when PWOFF | |
| %8828. | Get the command sent to ports when PWOFF | Port 13: NO Data when PWOFF | |
| %8829. | Get the command sent to ports when PWOFF | Port 14: NO Data when PWOFF | |
| %8830. | Get the command sent to ports when PWOFF | Port 15: NO Data when PWOFF | |
| %8831. | Get the command sent to ports when PWOFF | Port 16: NO Data when PWOFF | |
| USER/I/[x]:0706%; | Set the audio source of input [x] to HDMI embedded audio. Channel 04 in audio command is:0706% | ||
| USER/I/[x]:0707%; | Set the audio source of input [x] to analog audio. Channel 04 in audio command is:0707% | ||
| USER/I/[x]:0408%; | Restore the signal card to its factory default settings. | ||
| USER/O/[x]:0804%; | Set the resolution of output [x] to 720P 60Hz. | Resolution Out08 1280x720P | |
| USER/O/[x]:0813%; | Set the resolution of output [x] to 1080P 60Hz. | Resolution Out08 1920x1080P | |
| USER/O/[x]:0824%; | Set the resolution of output [x] to 1024x768 60Hz. | Resolution Out08 1024x768 | |
| USER/O/[x]:0840%; | Set the resolution of output [x] to 3840x2160 30Hz. | Resolution Out08 3840x2160 30Hz | |
| USER/O/[x]:0841%; | Set the resolution of output [x] to 3840x2160 60Hz. | Resolution Out08 3840x2160 60Hz | |
| USER/I/[x]:0409%; | RS232 pass-through control mode 1: Control far-end device from the RS232 port of this input card. | ||
| USER/I/[x]:0410%; | RS232 pass-through control mode 2(factory default): Control far-end device from the RS232 port of this Matrix Switcher. | ||
| USER/O/[x]:0409%; | RS232 pass-through control mode 1: Control far-end device from the RS232 port of this output card. | ||
| USER/O/[x]:0410%; | |||
| PortXX/InputMic. | Switch the audio input channel of port xx to MIC. | Port XX Switch to mic. | |
| PortXX/InputLine. | Switch the audio input channel of port xx to LINE. | Port XX Switch to line. | |
| PortXX/SetMicVol:XX. | Set the MIC volume of port xx to xx. | Port XX Volume of MIC: xx. (xx can be 0-60) | |
| PortXX/SetSourceVol:XX. | Set the source volume of port xx to xx. | Port XX Volume of SOURCE : xx. (xx can be 0-60) | |
| PortXX/MicVolume+. | Increase the MIC volume of port xx. | Port XX Volume of MIC : xx. (xx can be 0-60) | |
| PortXX/MicVolume-. | Decrease the MIC volume of port xx. | Port XX Volume of MIC : xx. (xx can be 0-60) | |
| PortXX/SourceVolume+. | Increase the source volume of port xx. | Port XX Volume of SOURCE : xx. | |
| PortXX/SourceVolume-. | Decrease the source volume of port xx. | Port XX Volume of SOURCE : xx. | |
| PortXX/SetStereo. | Switch the output audio mode of port xx to stereo. | Port XX Output is stereo mode. | |
| PortXX/SetMono. | Switch the output audio mode of port xx to mono. | Port XX Output is mono mode. | |
| PortXX/MicMute. | Mute the MIC audio of port xx. | Port XX Mic Mute. | |
| PortXX/MicUnmute. | Unmute the MIC audio of port xx. | Port XX Mic Unmute. | |
| PortXX/SourceMute. | Mute the source audio of port xx. | Port XX Source Mute. | |
| PortXX/SourceUnmute. | Unmute the source audio of port xx. | Port XX Source Unmute. | |
| %9921. | Inquire the input audio channel. | Port XX Switch to mic. Port XX Switch to line. | |
| %9922. | Inquire the output audio mode. | Port XX Output is stereo mode. Port XX Output is mono mode. | |
| %9923. | Inquire the mute status of MIC audio. | Port XX Mic Mute. Port XX Mic Unmute. | |
| %9925. | Inquire the mute status of source audio. | Port XX Source Mute. Port XX Source Unmute. | |
| %9926. | Inquire the volume of MIC audio. | Port XX Volume of MIC : xx. | |
| %9928. | Inquire the volume of source audio. | Port XX Volume of SOURCE : xx. |
TCP/IP Commands1 commandsActive
ConnectionIP: 192.168.0.178; Subnet Mask: 255.255.255.0; Gateway: 192.168.0.1; Serial Port: 4001↓ CSV
Source: manual, chapter TCP/IP Control, page 38
| Command | Description | Response | |
|---|---|---|---|
| Commands are the same with RS232 commands listed in 4.3.3 RS232 Communication Commands | You can enter commands to control the Matrix Switcher after successful TCP/IP connection using TCPUDP software or any TCP/IP communication software. | Here you will receive the feedback when a command is sent. |