← Products
4x2 4K Multiformat Presentation Switcher with KVM and Scaler Set
Discontinued

PT-PSW-42

4x2 4K Multiformat Presentation Switcher with KVM and Scaler Set

The PureTools Teleconference Scaler Switcher 4x2 is a presentation switcher with 2 HDMI inputs and 1 DisplayPort or VGA input, featuring mirrored HDMI and HDBaseT outputs. It supports resolutions up to 4K UltraHD 30Hz …

ManualControl (TCP/IP)FAQSpecificationsDatasheetCE declaration ↗

Available control interfaces. Expand an active type to see the full command table.

RS-232 Commands60 commandsActive
ConnectionBaud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none The end mark of command is “<CR><LF>”.↓ CSV

Source: manual, chapter RS232 Control, page 20

CommandDescriptionExampleResponse
SWIN H1Switch to 1-HDMI input.Switch to HDMI1
SWIN H2Switch to 2-HDMI input.Switch to HDMI2
SWIN DPSwitch to 3-DP input.Switch to DP
SWIN VGSwitch to 4-VGA input.Switch to VGA
SWIN RXHDMISwitch to RX HDMI input.Switch to RX HDMI
AUTO 01Enable auto-switching.Auto Switching
AUTO 00Enable manual-switching.Manual Switching
?GET INGet the input source of Transmitter. (HDMI1,HDMI2,DP,VGA)TX Device Input: HDMI1
?GET INGet the input source of Receiver. (HDMI,HDBT)RX Device Input: HDMI
?GET AUTOGet the switching mode.Manual Switching/Auto Switching
VGAAAuto-adjust the input parameter (VGA only).VGA Input Auto
AUMT S1Mute source audio.Audio Mute Source: Enable
AUMT S0Unmute source audio.Audio Mute Source: Disable
AUMT V1Mute VGA auxiliary input audio.Audio Mute VGA: Enable
AUMT V0Unmute VGA auxiliary input audio.Audio Mute VGA: Disable
?GET AUMTGet the Source mute status.Audio Mute Source: Enable
?GET AUMTGet the VGA auxiliary audio mute status.Audio Mute VGA: Enable
VOLS APTurn up the source audio volume (xx=00~60).Source Volume: xx
VOLS ANTurn down the source audio volume (xx=00~60).Source Volume: xx
VOLV APTurn up the VGA auxiliary audio volume (xx=00~60).VGA Volume: xx
VOLV ANTurn down the VGA auxiliary audio volume (xx=00~60).VGA Volume: xx
VOLS xxSet the source audio volume (xx=00~60).Source Volume: xx
VOLV xxSet the VGA auxiliary audio volume (xx=00~60).VGA Volume: xx
?GET VOLGet the source audio volume (xx=00~60).Source Volume: xx
?GET VOLGet the VGA auxiliary audio volume (xx=00~60).VGA Volume: xx
TRES 01Set the output resolution for Transmitter to 3840x2160@30Hz.TX Device Resolution: 3840x2160
TRES 02Set the output resolution for Transmitter to 1920X1080.TX Device Resolution: 1920x1080
TRES 03Set the output resolution for Transmitter to 1280x720.TX Device Resolution: 1280x720
RRES 01Set the output resolution for Receiver to 3840x2160@30Hz.RX Device Resolution: 3840x2160
RRES 02Set the output resolution for Receiver to 1920x1080.RX Device Resolution: 1920x1080
RRES 03Set the output resolution for Receiver to 1280x720.RX Device Resolution: 1280x720
?GET RESGet the output resolution for Transmitter.TX Device Resolution: 1920x1080
?GET RESGet the output resolution for Receiver.TX Device Resolution: 1920x1080
?GET TIMECheck the auto power-off mode.Auto Switch Mode no input to shutdown time: Disable Manual Switch Mode no input to shutdown time: Disable
TIME ADAuto Switch Mode: Disable the auto power-off function.Auto Switch Mode no input to shutdown time: Disable
TIME A1Auto Switch Mode: Set the auto power-off time to 1 minute when No signal input.Auto Switch Mode no input to shutdown time: 1 minutes
TIME A2Auto Switch Mode: Set the auto power-off time to 2 minute when No signal input.Auto Switch Mode no input to shutdown time: 2 minutes
TIME A3Auto Switch Mode: Set the auto power-off time to 5 minute when No signal input.Auto Switch Mode no input to shutdown time: 5 minutes
TIME A4Auto Switch Mode: Set the auto power-off time to 10 minute when No signal input.Auto Switch Mode no input to shutdown time: 10 minutes
TIME MDManual Switch Mode: Disable auto power-off time function.Manual Switch Mode no input to shutdown time: Disable
TIME M1Manual Switch Mode: Set the power-off time to 1 minute.Manual Switch Mode no input to shutdown time: 1 minutes
TIME M2Manual Switch Mode: Set the power-off time to 2 minute.Manual Switch Mode no input to shutdown time: 2 minutes
TIME M3Manual Switch Mode: Set the power-off time to 5 minute.Manual Switch Mode no input to shutdown time: 5 minutes
TIME M4Manual Switch Mode: Set the power-off time to 10 minute.Manual Switch Mode no input to shutdown time: 10 minutes
RLY1 ONTurn on the Relay 1.Relay 1 on
RLY1 OFFTurn off the Relay 1.Relay 1 off
RLY2 ONTurn on the Relay 2.Relay 2 on
RLY2 OFFTurn off the Relay 2.Relay 2 off
EDID DFThe source device obtains the default EDID 3840x2160@30Hz.EDID: Initial
EDID USLoad customize EDID data from U-disk.EDID: User
?GET EDIDGet EDID status.EDID: Initial/ User
SFUD TXUpdate the software of Transmitter.TX Device Software Update
SFUD RXUpdate the software of Receiver.RX Device Software Update
?GET REVGet the system version.Vx.x.x
FRSTRestore to factory defaults.Factor Reset
WAKEWake up the system.Wake Up
STBYLet this system enter in standby mode.Go To Standby
?GET IPGet the IP address.192.168.0.178!
/+pb:xxxxxxxxxSend ASCII command to control the third party device based on RS232 pass-through function. p = 0~1 is for RS232 control mode. When the "p=0", send command to control the local third party device which is connected to the transmitter. When the "p=1", the command is sent to control remote third party device which is connected to the receiver. b = 0~6 is for baud rate. b | Baud Rate 0 | 2400 1 | 4800 2 | 9600 3) xxxxxxxxx is for ASCII data (max 48 Byte)./+12:123456789
/-pb:xx xx xx xxSend HEX command to control the third party device based on RS232 pass-through function. b | Baud Rate 0 | 2400 1 | 4800 2 | 9600 3 | 19200 4 | 38400 5 | 57600 6 | 115200 3) xx xx xx xx is for HEX data (max 48 Byte)./-12:30 31 32 33 34
Staff sign-in