Fuori produzionePossibile alternativa: PT-PSW-21HC-KVM
PT-PSW-21C
Switcher di presentazione multiformato 2x1 4K 18Gbps con KVM
Il Switcher KVM PureTools 2x1 (HDMI, USB-C) consente di commutare tra 1 segnale HDMI e 1 USB-C verso un singolo Output HDMI, supportando una larghezza di banda di 18Gbps per risoluzioni fino a 4K UltraHD 60Hz. Il …
ManualeComandi (TCP/IP)FAQScheda tecnicaAlternativa disponibileFirmwareCEInterfacce di controllo disponibili. Espanda un tipo attivo per visualizzare la tabella completa dei comandi.
Nessun comando corrispondente.
Comandi RS23235 comandiAttivo
ConnessioneRS232 Communication Protocol Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none All commands must end with “<CR><LF>”. In the commands, “[”and “]” are symbols for easy reading and do not need to be typed in actual operation.↓ CSV
Fonte: manuale, capitolo RS232 Command, pagina 22
| Comando | Descrizione | Risposta | |
|---|---|---|---|
| #GET_FIRMWARE_VERSION | Ottieni la versione del firmware. | @V1.0.0 | |
| #FACTORY_RESET | Ripristino alle impostazioni di fabbrica. | @FACTORY_RESET | |
| #REBOOT | System reboot | @REBOOT | |
| #HELP | Get the command details. Example: #HELP SET_AV Feedback: @SELECT VIDEO AND AUDIO INPUT PORT | ||
| #SET_AV PARAM1 PARAM1=H,C H - HDMI C - TYPE-C | |||
| #SET_AV H | Switch to HDMI input. | @AV H | |
| #SET_AV C | Switch to USB-C input. | @AV C | |
| #GET_AV | Ottieni la sorgente di ingresso attuale. | @AV H @AV C | |
| #SET_AUTO_SWITCH 1 | Abilita la modalità di commutazione automatica. | @AUTO_SWITCH 1 | |
| #SET_AUTO_SWITCH 0 | Disable auto switching mode. | @AUTO_SWITCH 0 | |
| #GET_AUTO_SWITCH | Ottieni lo stato del commutamento automatico. | @AUTO_SWITCH 1 @AUTO_SWITCH 0 | |
| #UPLOAD_USER_EDID [X] X =1~5, represents the EDID, its DIP switch status shows as below: | X DIP Switch Status 1 1011 2 1100 3 1101 4 1110 5 1111 Operation: Prepare the EDID file (.bin). Set the 4-pin DIP switch status, for example: “1011”. Send the command “#UPLOAD_USER_EDID 1.”, and the feedback is “@USER_EDID 1 READY PLEASE SEND EDID DATA IN 10S”. Send the EDID file (.bin). If successfully upload, the feedback is: “OK”. | ||
| #SET_SYNCACT_CEC 1 | Enable the function of automatically sending CEC commands. When detecting video input signal or not detecting any video signal, the switcher will automatically send the corresponding CEC command to control the display device. | @SYNCACT_CEC 1 | |
| #SET_SYNCACT_CEC 0 | Disable the function of automatically sending CEC commands. | @SYNCACT_CEC 0 | |
| #GET_SYNCACT_CEC | Ottieni lo stato della funzione di invio automatico dei comandi CEC. | @SYNCACT_CEC 1 | |
| #SET_SYNCACT_RS232 1 | Enable the function of automatically sending RS232 commands. When detecting video input signal or not detecting any video signal, the switcher will automatically send the corresponding RS232 command to control the display device. | @SYNCACT_RS232 1 | |
| #SET_SYNCACT_RS232 0 | Disable the function of automatically sending RS232 commands. | @SYNCACT_RS232 0 | |
| #GET_SYNCACT_RS232 | Ottieni lo stato della funzione di invio automatico dei comandi RS232. | @SYNCACT_RS232 1 | |
| #SET_DTIME [PARAM1]:[PARAM2] | When not detecting video input signal, set the auto power-off time of display device to [PARAM1]: [PARAM2]. The default time is 15 minutes. [PARAM1]=0~30 minutes. [PARAM2]=0~1800 seconds. | #SET_DTIME 1:30 @DTIME 1:30 | |
| #GET_DTIME | Get the auto power-off time of display device. | @DTIME 30:0 | |
| #SET_AUDIO_MUTE | Mute/unmute the display audio through CEC and RS232 channels. | @AUDIO_MUTE_UNMUTE | |
| #SET_VOL + | Increase the display audio through CEC and RS232 channels. | @VOL - | |
| #SET_VOL - | Decrease the display audio through CEC and RS232 channels. | @VOL + | |
| #SET_DISPLAY 1 | Accendi il display. | @DISPLAY 0 | |
| #SET_DISPLAY 0 | Spegni il display. | @DISPLAY 1 | |
| #SET_RS232_BAUD 0 | Set the RS232 baud rate to 115200. | @RS232_BAUD 0 | |
| #SET_RS232_BAUD 1 | Set the RS232 baud rate to 57600. | @RS232_BAUD 1 | |
| #SET_RS232_BAUD 2 | Set the RS232 baud rate to 38400. | @RS232_BAUD 2 | |
| #SET_RS232_BAUD 3 | Set the RS232 baud rate to 19200. | @RS232_BAUD 3 | |
| #SET_RS232_BAUD 4 | Set the RS232 baud rate to 9600. | @RS232_BAUD 4 | |
| #SET_RS232_BAUD 5 | Set the RS232 baud rate to 4800. | @RS232_BAUD 5 | |
| #SET_RS232_BAUD 6 | Set the RS232 baud rate to 2400. | @RS232_BAUD 6 | |
| #GET_RS232_BAUD | Ottieni la velocità di trasmissione RS232. | @RS232_BAUD 0 @RS232_BAUD 1 @RS232_BAUD 2 @RS232_BAUD 3 @RS232_BAUD 4 @RS232_BAUD 5 @RS232_BAUD 6 | |
| #SET_ON_[PARAM1]_[PARAM2]:XXXX | Set the ASCII RS232 command XXXX to be sent to control the third-party device when the DISPLAY ON button is pressed. [PARAM1] = 00~06 (Baud Rate) 00 - 115200 01 - 57600 02 - 38400 03 - 19200 04 - 9600 05 - 4800 06 - 2400 [PARAM2] = 00~99. The delay time of sending command. XXXX: Any ASCII code (up to 48 bytes). | #SET_ON_05_30:1234567 @BAUDRATE: 4800 @DELAY TIME: 30 s @DISPLAY ON TO SEND:1234567 | |
| #SET_H_ON_[PARAM1]_[PARAM2]:XX XX | Set the HEX RS232 command XX XX to be sent to control the third-party device when the DISPLAY ON button is pressed. [PARAM1] = 00~06 (Baud Rate) 00 - 115200 01 - 57600 02 - 38400 03 - 19200 04 - 9600 05 - 4800 06 - 2400 [PARAM2] = 00~99. The delay time of sending command. | #SET_H_ON_05_30:31 32 33 34 35 @BAUDRATE: 4800 @DELAY TIME: 30 s @DISPLAY ON HEX TO SEND:31 32 33 34 35 |