Descatalogado
PT-PMS-42S
Conjunto de matriz de presentación multiformato 4x2 4K a 18 Gbps sin interrupciones
El Matrix de Presentación Multiformato Seamless 4x2 4K 18Gbps es un Switcher AV que admite señales HDMI y USB-C con salidas Matrix HDMI y HDBaseT. Ofrece resoluciones de salida escaladas de hasta 4K@60Hz, 4:4:4 vía HDMI …
ManualComandos (TCP/IP)FAQCEInterfaces de control disponibles. Despliegue un tipo activo para ver la tabla completa de comandos.
No hay comandos coincidentes.
Comandos RS23278 comandosActivo
ConexiónBaud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none All commands needs to be ended with “ <CR><LF> ”. In the commands, “ [ ”and “ ] ” are symbols for easy reading and do not need to be typed in actual operation. Type the command carefully, it is case-sensitive.↓ CSV
Fuente: manual, capítulo RS232 Command, página 42
| Comando | Descripción | Ejemplo | Respuesta | |
|---|---|---|---|---|
| #SYS_SET_DEVICE_MODLE **** | Renombrar el modelo del sistema a ****. | #SYS_SET_DEVICE_MODLE PT-PMS-42S PT-PMS-42S | ||
| #SET_PWR_STATE ON | Sistema encendido. | @PWR_STATE PWON | ||
| #SET_PWR_STATE OFF | Sistema en espera. | @PWR_STATE PWOFF | ||
| #GET_PWR_STATE | Obtener el estado de energía del sistema. | @PWR_STATE PWON @PWR_STATE PWOFF | ||
| #SET_KEYPAD_LOCK ON | Bloquear los botones del panel frontal. | @KEYPAD_LOCK ON | ||
| #SET_KEYPAD_LOCK OFF | Desbloquear botones del panel frontal. | @KEYPAD_LOCK OFF | ||
| #GET_KEYPAD_LOCK | Obtener el estado de bloqueo de los botones del panel frontal. | @KEYPAD_LOCK ON @KEYPAD_LOCK OFF | ||
| #GET_DEVICE_TYPE | Obtener modelo del sistema. | PT-PMS-42S | ||
| #GET_DEVICE_IPADDR | Obtener dirección IP de la GUI. | @IP_ADDR: 192.168.0.178 | ||
| #FACTORY_RESET | Restablecer a valores predeterminados de fábrica. | FACTORY_RESET | ||
| #GET_DEVICE_FIRMWAREINF | Obtener versión del firmware. | FIRMWARE V1.0.0 | ||
| #SET_PORT_RELAY 01 ON | Activar PoC para el puerto de salida HDBT. El Receiver PT-HDBT-210-RX puede ser alimentado por el switcher. | @PORT_RELAY 01 ON | ||
| #SET_PORT_RELAY 01 OFF | Apagar PoC para el puerto de salida HDBT. | @PORT_RELAY 01 OFF | ||
| #GET_PORT_RELAY 01 | Obtener estado PoC. | @PORT_RELAY 00 @PORT_RELAY 01 | ||
| #SET_BADURATE_MODE [PARAM] | Configure la velocidad en baudios del Switcher a [PARAM]. [PARAM]=01~07 [PARAM] Velocidad en baudios 01 2400 02 4800 03 9600 04 19200 05 38400 06 57600 07 115200 | #SET_BADURATE_MODE 05 | ||
| #UPDATE_MODE MAIN [PARAM] | Actualizar el IC 3458 del puerto [PARAM]. [PARAM]=01~04 (puerto de entrada). [PARAM]=05~06 (puerto de salida). | #UPDATE_MODE MAIN 01 | @UPDATE_MODE MAIN 01 @Updating... @UPDATE_MODE MAIN: SUCCESS | |
| #UPDATE_MODE HDCP22 [PARAM] | Actualizar el HDCP 2.2 del puerto [PARAM]. [PARAM]=01~04 (puerto de entrada). [PARAM]=05~06 (puerto de salida). | #UPDATE_MODE HDCP22 01 | @UPDATE_MODE HDCP22 01 @Updating... @UPDATE_MODE HDCP22: SUCCESS | |
| #SET_MODE_DOWNSCLAR ON | Habilitar la reducción de resolución de video. | @DOWNSCLAR_MODE ON | ||
| #SET_MODE_DOWNSCLAR OFF | Desactivar la reducción de resolución de video. | @DOWNSCLAR_MODE OFF | ||
| #GET_MODE_DOWNSCLA | Obtener estado de reducción de resolución de video. | @DOWNSCLAR_MODE ON @DOWNSCLAR_MODE OFF | ||
| #SET_AUTO_SWITCH [PARAM] ON | Habilitar el modo de conmutación automática para la salida HDMI o HDBT. [PARAM] = 01 (HDMI)/02 (HDBT) | #SET_AUTO_SWITCH 01 ON @AUTOSWITCH 01 ON | ||
| #SET_AUTO_SWITCH [PARAM] OFF | Desactivar el modo de conmutación automática para la salida HDMI o HDBT. [PARAM] = 01 (HDMI)/02 (HDBT) | #SET_AUTO_SWITCH 01 OFF @AUTOSWITCH 01 OFF | ||
| #GET_AUTO_SWITCH | Obtener el modo de conmutación automática de las salidas HDMI y HDBT. | @AUTOSWITCH 01 ON @AUTOSWITCH 02 OFF | ||
| #SET_AV [INPARAM] TO [OUTPARAM1] [OUTPARAM2]… | Cambiar entrada [INPARAM] a salida [OUTPARAM1] [OUTPARAM2]… [INPARAM]=01 ~ 04 [OUTPARAM1] [OUTPARAM2]…= 01 ~ 02, TODOS | #SET_AV 01 TO 02 #SET_AV 01 TO 01 02 #SET_AV 04 TO ALL @AV 01 TO 02 @AV 01 TO 01 02 @AV 04 TO ALL | ||
| #GET_AV | Obtener el canal de entrada en cada canal de salida uno por uno. | @Video&Audio OUT 01 02 IN 04 04 | ||
| #GET_AV OUT [PARAM] | Obtener el canal de entrada en la salida [PARAM]. [PARAM]=01~02. | #GET_AV OUT 01 @AV 01 TO 01 | ||
| #GET_AV IN [PARAM] | Obtener el canal de salida en la entrada [PARAM]. [PARAM]=01~04. | #GET_AV IN 01 @AV 01 TO 01 02 | ||
| #SAVE_PRESET_MODE [PARAM] | Guardar el estado actual de conmutación en el guardado [PARAM]. [PARAM]=01~10. | #SAVE_PRESET_MODE 01 @SAVE_PRESET_MODE 01 | ||
| #RECALL_PRESET_MODE [PARAM] | Recordar el preset [PARAM]. [PARAM]=01~10. | #RECALL_PRESET_MODE 04 @CALL_PRESET_MODE 04 @Video&Audio OUT 01 02 IN 01 03 | ||
| #CLR_PRESET_MODE [PARAM] | Borrar el preajuste [PARAM]. [PARAM]=01~10. | #CLR_PRESET_MODE 01 @CLEAR_PRESET_MODE 01 | ||
| #SET_IIS_SEL [PARAM] | Establecer la fuente de audio del puerto de salida de audio (L+R) a [PARAM]. [PARAM]=01 ~ 02 01=audio de salida HDMI 02=audio de salida HDBT | #SET_IIS_SEL 01 @IIS_AUDIO 01 | ||
| #GET_IIS_SEL | Obtener la fuente de audio del puerto de salida de audio (L+R). | @IIS_AUDIO 01 | ||
| #SET_SPDIF_SEL [PARAM] | Establecer la fuente de audio del puerto de salida SPDIF a [PARAM]. [PARAM]=01 ~ 03 01=audio de salida HDMI 02=audio de salida HDBT 03=audio ARC desde el receiver | #SET_SPDIF_SEL 01 @SPDIF_AUDIO 01 | ||
| #GET_SPDIF_SEL | Obtener la fuente de audio del puerto de salida SPDIF. | @SPDIF_AUDIO 01 | ||
| #SET_AUDIO_ARC ON | Activar modo ARC del Receiver PT-HDBT-210-RX. | @SET_AUDIO_ARC ON | ||
| #SET_AUDIO_ARC OFF | Desactivar el modo ARC del Receiver PT-HDBT-210-RX. | @SET_AUDIO_ARC OFF | ||
| #GET_AUDIO_ARC | Obtener estado ARC. | @SET_AUDIO_ARC ON @SET_AUDIO_ARC OFF | ||
| #SET_AUDIO_MUTE [PARAM] ON | Silenciar el audio [PARAM]. [PARAM]=01~05, ALL 01=Audio de salida HDMI 02=Audio de salida HDBT 03=Audio MIX 04=Audio MIC 05=Audio L+R ALL=Todo el audio. | #SET_AUDIO_MUTE 01 ON #SET_AUDIO_MUTE ALL ON @AUDIO_MUTE 01 ON @AUDIO_MUTE ALL ON | ||
| #SET_AUDIO_MUTE [PARAM] OFF | Activar el audio [PARAM]. [PARAM]=01~05, ALL 01=Audio de salida HDMI 02=Audio de salida HDBT 03=Audio MIX 04=Audio MIC 05=Audio de salida L+R ALL=Todo el audio. | #SET_AUDIO_MUTE 01 OFF #SET_AUDIO_MUTE ALL OFF @AUDIO_MUTE 01 OFF @AUDIO_MUTE ALL OFF | ||
| #GET_AUDIO_MUTE [PARAM] | Obtener el estado de salida de audio [PARAM]. [PARAM]=01~05, ALL 01=Audio de salida HDMI 02=Audio de salida HDBT 03=Audio MIX 04=Audio MIC 05=Audio de salida L+R ALL=Todo el audio. | #GET_AUDIO_MUTE 01 #GET_AUDIO_MUTE ALL @AUDIO MUTE 01 ON @AUDIO MUTE OUT 01 02 03 04 05 STA 01 01 01 01 01 | ||
| #SET_VOL [PARAM1] [PARAM2] | Set the volume of [PARAM1] audio to [PARAM2]. [PARAM1]=01~05 01=HDMI output audio 02=HDBT output audio 03=MIX audio 04=MIC audio 05=L+R output audio [PARAM2]=0~60 | #SET_VOL 01 60 @VOL HDMI 60 | ||
| #GET_VOL [PARAM] | Obtener el volumen de audio de la salida [PARAM]. [PARAM]= HDMI, HDBT, ALL. | #GET_VOL HDMI #GET_VOL ALL @VOL HDMI 60 @VOL HDBT 60 @VOL MIX 60 @VOL MIC 30 @VOL L+R 30 | ||
| #SET_AUDIO_EMBEDDED ON | Seleccionar el audio balanceado externo (5 pines) para incrustar en la entrada 1.HDMI. | @AUDIO_EMBEDDED ON | ||
| #SET_AUDIO_EMBEDDED OFF | Seleccionar la transmisión de audio HDMI interna del dispositivo fuente para la entrada 1.HDMI. | @AUDIO_EMBEDDED OFF | ||
| #GET_AUDIO_EMBEDDED 01 | Obtener la fuente de audio de la entrada HDMI 1. | @AUDIO_EMBEDDED ON @AUDIO_EMBEDDED OFF | ||
| #SET_AUDIO_MIX [PARAM1] [PARAM2] | Habilitar/deshabilitar la salida de audio [PARAM1] para mezclar con el audio MIX. [PARAM1]=01~02, ALL 01=Salida HDMI 02=Salida HDBT ALL=Todas las salidas [PARAM2]=ON/OFF | #SET_AUDIO_MIX 01 ON #SET_AUDIO_MIX ALL ON @AUDIO_MIX 01 ON @AUDIO_MIX 01 OFF @AUDIO_MIX ALL OFF @AUDIO_MIX ALL ON | ||
| #GET_AUDIO_MIX [PARAM] | Obtener el estado de audio MIX de la salida [PARAM]. [PARAM]=01~02, ALL 01=Salida HDMI 02=Salida HDBT ALL=Todas las salidas | #GET_AUDIO_MIX 01 #GET_AUDIO_MIX ALL @AUDIO_MIX 01 ON @AUDIO_MIX 02 OFF | ||
| #SET_AUDIO_MIC [PARAM1] [PARAM2] | Habilitar/deshabilitar la salida de audio [PARAM1] para mezclar con el audio del micrófono. [PARAM1]=01~02, ALL 01=Salida HDMI 02=Salida HDBT ALL=Todas las salidas [PARAM2]=ON/OFF | #SET_AUDIO_MIC 01 ON #SET_AUDIO_MIC ALL ON @AUDIO_MIC 01 ON @AUDIO_MIC 01 OFF @AUDIO_MIC ALL OFF @AUDIO_MIC ALL ON | ||
| #GET_AUDIO_MIC [PARAM] | Obtener el estado de audio MIC de la salida [PARAM]. [PARAM]=01~02, ALL 01=Salida HDMI 02=Salida HDBT ALL=Todas las salidas | #GET_AUDIO_MIC 01 #GET_AUDIO_MIC ALL @AUDIO_MIC 01 OFF @AUDIO_MIC 02 OFF | ||
| #SET_OUTPUT_RES [PARAM1] TO [PARAM2] | Set the output resolution of output [PARAM2] to [PARAM1]. [PARAM2]=01~02 [PARAM2] Output 01 HDMI 02 HDBT [PARAM1]=1~10 1 4K@60HZ 4:4:4 2 4K@30Hz 4:4:4 3 1920X1200@60Hz 4 1080P@60Hz 5 1080P@50Hz 6 1600x1200@60Hz 7 1360x768@60Hz 8 1024x768@60Hz 9 720P@60Hz 10 720P@50Hz | #SET_OUTPUT_RES 01 TO 01 @OUTPUT_RES 4k@60 TO 01 | ||
| #GET_OUTPUT_RES [PARAM] | Obtener la resolución de vídeo de la salida [PARAM]. [PARAM]=01~02, ALL | #GET_OUTPUT_RES 01 @OUTPUT RES 1080@60 TO 01 | ||
| #SET_EDID_MODE CAL:[PARAM1] TO [PARAM2] | La entrada HDMI [PARAM2] invoca el EDID incorporado [PARAM1]. [PARAM1]=01~03 (EDID) [PARAM2]=01~03 (1.HDMI IN~3.HDMI IN) [PARAM1] EDID 01 1080P@60Hz 2CH 02 4K@30Hz 4:4:4 2CH 03 4K@60Hz 4:4:4 2CH | #SET_EDID_MODE CAL:01 TO 02 @EDID_MODE CAL:01 TO 02 | ||
| #SET_EDID_MODE LRN:[PARAM1] TO [PARAM2] | Configurar los datos EDID de la salida [PARAM1] a la entrada [PARAM2]. | |||
| #SEND_CECCMD [port]:00 | Confirmar operación (Enter). | #SEND_CECCMD 03:00 [CEC]: blue ray OK. | ||
| #SEND_CECCMD [port]:01 | UP. | #SEND_CECCMD 03:01 [CEC]: blue ray up. | ||
| #SEND_CECCMD [port]:02 | ABAJO. | #SEND_CECCMD 03:02 [CEC]: blue ray down. | ||
| #SEND_CECCMD [port]:03 | IZQUIERDA. | #SEND_CECCMD 03:03 [CEC]: blue ray left. | ||
| #SEND_CECCMD [port]:04 | DERECHO. | #SEND_CECCMD 03:04 [CEC]: blue ray right. | ||
| #SEND_CECCMD [port]:09 | Volver al submenú. | #SEND_CECCMD 03:09 [CEC]: blue ray menu. | ||
| #SEND_CECCMD [port]:0D | Salir. | #SEND_CECCMD 03:0D [CEC]: blue ray Exit. | ||
| #SEND_CECCMD [port]:41 | Subir volumen. | #SEND_CECCMD 03:41 [CEC]: blue ray Volume Up. | ||
| #SEND_CECCMD [port]:42 | Bajar volumen. | #SEND_CECCMD 03:42 [CEC]: blue ray Volume Down | ||
| #SEND_CECCMD [port]:44 | Reproducir. | #SEND_CECCMD 03:44 [CEC]: blue ray play. | ||
| #SEND_CECCMD [port]:45 | Detener. | #SEND_CECCMD 03:45 [CEC]: blue ray stop. | ||
| #SEND_CECCMD [port]:46 | Pausa. | #SEND_CECCMD 03:46 [CEC]: blue ray pause. | ||
| #SEND_CECCMD [port]:48 | Rebobinar | #SEND_CECCMD 03:48 [CEC]: blue ray backward. | ||
| #SEND_CECCMD [port]:49 | Avance rápido. | #SEND_CECCMD 03:49 [CEC]: blue ray forward. | ||
| #SEND_CECCMD [port]:4B | Avanzar. | #SEND_CECCMD 03:4B [CEC]: blue ray skid forward. | ||
| #SEND_CECCMD [port]:4C | Atrás. | #SEND_CECCMD 03:4C [CEC]: blue ray skid backward. | ||
| #SEND_CECCMD [port]:6C | Apagar. | #SEND_CECCMD 03:6C [CEC]: Source Power off. | ||
| #SEND_CECCMD [port]:6D | Encender. | #SEND_CECCMD 03:6D [CEC]: Source Power on. | ||
| #SEND_CECCMD [port]:34 | Selección de canal de entrada. | #SEND_CECCMD 04:34 [CEC]: TV input select | ||
| #SEND_CECCMD [port]:41 | Subir volumen. | #SEND_CECCMD 04:41 [CEC]: TV VOL + | ||
| #SEND_CECCMD [port]:42 | Bajar volumen. | #SEND_CECCMD 04:42 [CEC]: TV VOL - | ||
| #SEND_CECCMD [port]:43 | Silenciar | #SEND_CECCMD 04:43 [CEC]: TV VOL Mute | ||
| #SEND_CECCMD [port]:36 | Apagar. | #SEND_CECCMD 04:36 [CEC]: TV Power off | ||
| #SEND_CECCMD [port]:04 | Encender. | #SEND_CECCMD 04:04 [CEC]: TV Power on | ||
| #SEND_[PARAM1]_[PARAM2]_[PARAM3]:XXXX | Send the ASCII or HEX command to control the third-party device. [PARAM1]=A/H: Represents the command format. [PARAM1] Command Format A ASCII H HEX [PARAM2]=01~02: Represents the RS232 port. [PARAM2] RS232 Port 01 The RS232 port of the switcher. 02 The RS232 port of the far-end HDBaseT receiver. [PARAM3]=01~07: Represents the baud rate |
RS232 Command5 comandosActivo
Fuente: manual, capítulo RS232 Command, página 53
| Comando | Descripción | Ejemplo | Respuesta | |
|---|---|---|---|---|
| #SEND_[PARAM1]_[PARAM2]_[PARAM3]:XXXX | Send the ASCII or HEX command to control the third-party device. [PARAM1]=A/H: Represents the command format. [PARAM1] | Command Format A | ASCII H | HEX [PARAM2]=01~02: Represents the RS232 port. [PARAM2] | RS232 Port 01 | The RS232 port of the switcher. 02 | The RS232 port of the far-end HDBaseT receiver. [PARAM3]=01~07: Represents the baud rate of third-party device. [PARAM3] | Baud Rate 01 | 2400 02 | 4800 03 | 9600 04 | 19200 05 | 38400 06 | 57600 07 | 115200 XXXX: ASCII or HEX characters. | #SEND_A_01_05:123456789 #SEND_H_02_05:30 31 32 33 34 | ||
| #SET_ON_[PARAM1]_[PARAM2]_[PARAM3]:XXXX | When power on system, automatically send the ASCII or HEX command to the third-party device. [PARAM1]=A/H: Represents the command format. [PARAM1] | Command Format A | ASCII H | HEX [PARAM2]=01~02: Represents the RS232 port. [PARAM2] | RS232 Port 01 | The RS232 port of the switcher. 02 | The RS232 port of the far-end HDBaseT receiver. [PARAM3]=01~07: Represents the baud rate of third-party device. [PARAM3] | Baud Rate 01 | 2400 02 | 4800 03 | 9600 04 | 19200 05 | 38400 06 | 57600 07 | 115200 XXXX: ASCII or HEX characters. | #SET_OF_A_01_03:123456789 #SET_OF_H_02_03:30 31 32 33 34 | ||
| #GET_ON_[PARAM1]_[PARAM2] | Get the feedback command which to be sent to the third-party device when the system is powered on. [PARAM1]=01~02: Represents the RS232 port. [PARAM1] | RS232 Port 01 | The RS232 port of the switcher. 02 | The RS232 port of the far-end HDBaseT receiver. [PARAM2]=01~07: Represents the baud rate of third-party device. [PARAM2] | Baud Rate 01 | 2400 02 | 4800 03 | 9600 04 | 19200 05 | 38400 06 | 57600 07 | 115200 | |||
| #SET_OF_[PARAM1]_[PARAM2]_[PARAM3]:XXXX | When power off system or enter system standby mode, automatically send the ASCII or HEX command to the third-party device. [PARAM1]=A/H: Represents the command format. [PARAM1] | Command Format A | ASCII H | HEX [PARAM2]=01~02: Represents the RS232 port. [PARAM2] | RS232 Port 01 | The RS232 port of the switcher. 02 | The RS232 port of the far-end HDBaseT receiver. [PARAM3]=01~07: Represents the baud rate of third-party device. [PARAM3] | Baud Rate 01 | 2400 02 | 4800 03 | 9600 04 | 19200 05 | 38400 06 | 57600 07 | 115200 XXXX: ASCII or HEX characters. | #SET_OF_A_01_03:123456789 #SET_OF_H_02_03:30 31 32 33 34 | ||
| #GET_OF_[PARAM1]_[PARAM2] | Get the feedback command which to be sent to the third-party device when the system is powered off or enter standby mode. [PARAM1]=01~02: Represents the RS232 port. [PARAM1] | RS232 Port 01 | The RS232 port of the switcher. 02 | The RS232 port of the far-end HDBaseT receiver. [PARAM2]=01~07: Represents the baud rate of third-party device. [PARAM2] | Baud Rate 01 | 2400 02 | 4800 03 | 9600 04 | 19200 05 | 38400 06 | 57600 07 | 115200 |